Gateway Archives - Kepler Electronics

LRS232-802 Interface

Maen Sirhan — Fri, 29 Mar 2024 08:39:29 +0000

The LRS232-802 Interface expands a LOYTEC device by two RS-232 serial ports. It is connected to the USB port of the device and can be configured to run Modbus ASCII or a custom serial protocol implemented by a script module (script requires the L-IOT1 license). The LRS232-802 can be used with compatible L-INX Automation Servers, L-ROC Room Controllers, L-IOB I/O Controllers, L-DALI Controllers, L-GATE Universal Gateways, and with most L-VIS Touch Panels. Due to the USB bus interface, the device does not need a power supply and it is detected automatically.

Features

Provides two RS-232 ports
Configuration through web interface and LINX Configurator
Supports Modbus ASCII over RS-232
Supports custom serial protocols on RS-232 (L-IOT1 license required)

LRS232-802 Interface Products

LRS232-802

USB to 2x RS-232 Interface

The post LRS232-802 Interface appeared first on Kepler Electronics.

L-WLAN Wireless LAN Interface

Maen Sirhan — Fri, 29 Mar 2024 08:38:40 +0000

The L‑WLAN Interface expands a LOYTEC device with a wireless LAN connection. The wireless LAN Interface LWLAN‑800 can be used with L‑INX Automation Servers, L‑ROC Room Controllers, L-DALI Controllers, the L‑GATE Universal Gateways, L-IP Routers of the series ECTC, NIC709-IP3E100C Remote Network Interfaces, and with most L‑VIS Touch Panels. The L‑WLAN Interface only needs to be connected to the USB port. Due to the USB bus, the L‑WLAN device is energy supplied and detected automatically.

The L-WLAN Interface uses the protocol IEEE 802.11n improvements which significantly increase connection speed, is backward compatible to IEEE 802.11b & IEEE 802.11g, offers a link speed up to 150 Mbps, and an operation frequency/channel:

USA (FCC) 11 Channels: 2.412 GHz ~ 2.462 GHz
Europe (ETSI) 13 Channels: 2.412 GHz ~ 2.472 GHz
Japan 13 Channels: 2.412 GHz ~ 2.472 GHz

After attaching an LWLAN‑800 Interface to the USB port of the corresponding LOYTEC device, it is possible to connect it to an existing WLAN Access Point, create a WLAN Access Point.

The supplied antennas have a radial gain of up to +2 dBi and have to be mounted outside any metallized housing. To avoid any interferences, please keep a minimum distance of 0.5 m to any electronic devices which also operate with high-frequency signals such as of transformers, ballasts, computers, etc.

Features

Configuration through Web UI
Increased range through MIMO (multiple-input and multiple-output) – exploiting multipath propagation
Two external 2.4 GHz antennas supplied
Possibility for connecting external antennas via 2 SMA sockets (50 Ω)
Supports encryption WEP, WPA, and WPA2

L-WLAN Wireless LAN Interface Products

LWLAN-800

Wireless LAN Interface IEEE 802.11bgn

The post L-WLAN Wireless LAN Interface appeared first on Kepler Electronics.

LTE Interface

Maen Sirhan — Fri, 29 Mar 2024 08:37:50 +0000

The LTE Interface expands a LOYTEC device with a wireless mobile connection in the LTE network of a mobile provider. The LTE-800 Interface can be used with L‑INX Automation Servers, L‑ROC Room Controllers, L‑DALI Controllers, L-IOB I/O Controllers, the L‑GATE Universal Gateways, L‑IP Routers of the series ECTC, NIC709‑IP3E100C Remote Network Interfaces, and with L‑VIS Touch Panels. The LTE Interface simply needs to be connected to the USB port. Power to the LTE Interface is supplied through the 24 VDC power connector.

The integrated LTE modul uses the communication standard for LTE, UMTS/HSPA+ and GSM/GPRS/EDGE. It is approved for:

Carrier Certification: Deutsche Telekom/Verizon/AT&T/Sprint/U.S. Cellular/ Telus/T-Mobile/Rogers*
Regulatory Certification: SRRC/NAL/CCC/GCF/CE/ FCC/PTCRB/IC/Anatel/ IFETEL/KC/NCC/JATE/ TELEC/RCM/NBTC/ICASA/IMDA
Others: WHQL

After attaching an LTE-800 Interface to the USB port of the corresponding LOYTEC device, the LOYTEC device retrieves its IP configuration from the LTE provider. Together with the built-in VPN function, the LOYTEC device connects and can be accessed via the OpenVPN network technology. This ensures a secure communication path through the LTE network. All networking services of the LOYTEC device are available on the LTE interface and protected by the built-in firewall.

The LTE-800 Interface provides for an easy and simple solution to connect remote sites together via a VPN network and expose defined on-site services. Applications include remote management, energy monitoring, site visualization.

SMS transmission directly from the device is also enabled by the LTE-800 interface. Similar to E-Mails, SMS can contain configurable text and variable placeholders that resolve to data point content at the time of transmission. Together with an alarm data point the LTE-800 can be used as an SMS alarm notifier. The transmission of SMS can be limited to burst and long-term transmission rates.

* Under development

Features

Configuration through Web interface
Easy mobile site integration using VPN technology
OpenVPN compatible
SMS transmission and alarm notifier
Supports LTE standards

Tutorials

LTE-800 Tutorial

This video provides a detailed overview on the LTE-800 Interface.

LTE Interface Products

LTE-800

The post LTE Interface appeared first on Kepler Electronics.

KNX TP1 Interface

Maen Sirhan — Fri, 29 Mar 2024 08:35:51 +0000

The KNX-Interface LKNX‑300 allows the L‑INX Automation Servers, the L‑ROC Room Controllers, and the L‑GATE Universal Gateways to interface to KNX devices connected to a KNX TP1 Bus. The LKNX‑300 Interface needs to be connected to the EXT-Port on the L‑INX/L‑ROC/L‑GATE devices.

For the KNX integration, LOYTEC’s L‑INX/L‑ROC/L‑GATE devices use an ETS4/ETS5 project. The project data is exported from the ETS4/ETS5 software and then imported in the LOYTEC L‑INX Configurator. Thus, up to 250 or 1 000 data points from the KNX network can be used by the L‑INX/ L‑ROC/ L‑GATE devices on each port supporting KNXnet/ IP or KNX TP1.

Features

KNX TP1 Interface for L‑INX, L‑ROC, and L‑GATE
Access to a maximum of 250 or 1 000 KNX data points via KNX TP1 (L‑INX/L‑ROC/L‑GATE)
Configurable through ETS4/ETS5 software via XML import
Connected to the L-INX Automation Server, L-ROC Room Controller or L-GATE Gateway via port EXT

KNX TP1 Interface

LKNX-300

KNX interface to connect KNX TP1 devices

The post KNX TP1 Interface appeared first on Kepler Electronics.

L‑SMI Standard Motor Interface

Maen Sirhan — Fri, 29 Mar 2024 08:34:17 +0000

SMI is the acronym for Standard Motor Interface. SMI is a bus protocol used to control SMI sunblind motors for shading. Up to 16 motors can be connected to the bus. The L-SMI interface connects an SMI bus to a L‑INX, L‑ROC, or L‑DALI controller. Two SMI interface models are available.

The LSMI-800 connects a single SMI channel with up to 16 SMI motors to the EXT port of the L‑INX or L‑ROC controller. The bus power for the SMI bus is provided by the LSMI-800 interface but it is not galvanically isolated. Only SMI high voltage motors may be connected to the LSMI-800 interface.

The LSMI-804 connects up to four SMI channels with up to 64 SMI motors to the USB port of the L‑INX, L‑ROC, or L‑DALI controller. A galvanically isolated bus power for the SMI bus is provided by the LSMI-804 interface. Hence SMI high voltage or SMI low voltage motors may be connected to the LSMI-804 interfaces but high voltage and low voltage motors must not be mixed on one LSMI-804 interface. In addition to the four SMI bus channels, the LSMI-804 offers four relays controlled by the L‑INX, L‑ROC, or L‑DALI controller. Each relay can be used to cut power for the SMI motors on one channel if the motors are standing still. Cutting power when the motors are not moving reduces power consumption for SMI sunblind installations by more than 140 kWh per year for every channel.

Features

SMI Interface for L‑INX, L‑ROC, and L‑IOB Controller
Configuration through web interface
Calibration of the blind drives via web interface
Up to 16 blind drives per SMI port
Supports Standard Motor Interface, SMI bus systems according to Standard Motor Interface e.V. www.standard-motor-interface.com
Easy device replacement

L‑SMI Standard Motor Interface Products

LSMI-800

Standard Motor Interface for 16 motors via EXT port

LSMI-804

Standard Motor Interface for 64 motors, 4 SMI channels via USB

The post L‑SMI Standard Motor Interface appeared first on Kepler Electronics.

L-ENO EnOcean Interface

Maen Sirhan — Fri, 29 Mar 2024 08:33:13 +0000

L-ENO Datasheet
LENO-800, LENO-801, LENO-802 Installation Instructions
Certificates: EC / EnOcean
Downloads

The L‑ENO EnOcean Interface integrates wireless self-powered sensors and micro-energy devices seamlessly into building automation with the use of L‑INX Automation Servers, the L‑ROC Room Controller, the L‑DALI Controllers and the L‑GATE Universal Gateways. The L‑ENO Interface only needs to be connected to the USB port. The L‑ENO device is bus-powered over USB and detected automatically.

The L-ENO EnOcean Interfaces are available in three different versions for worldwide use:

LENO-800 Europe 868 MHz band
LENO-801 USA/Canada 902 MHz band
LENO-802 Japan 928 MHz band

Features

EnOcean Interface for L‑INX, L‑ROC, L‑GATE and L‑DALI
Supports all common EnOcean Profiles (EEPs) for sensors and actuators
Configurable through device templates supplied by the L-INX Configurator software
Web UI for Teach-In, signal strength, and value test
Easy device replacement
External antenna included
Connected to the L‑INX Automation Server, L‑ROC Room Controller, L-DALI Controllers or L‑GATE Gateway via USB 2.0
Support of multi-channel EnOcean devices
Encrypted wireless connection if the EnOcean device supports this function
Supports Mailbox function for sleepy actuators (e.g., battery-powered radiator valve)

L-ENO EnOcean Interface Products

LENO-800

EnOcean Interface 868 MHz Europe

LENO-801

EnOcean Interface 902 MHz USA/Canada

LENO-802

EnOcean Interface 928 MHz Japan

The post L-ENO EnOcean Interface appeared first on Kepler Electronics.

L-MBUS Level Converter

Maen Sirhan — Fri, 29 Mar 2024 08:32:25 +0000

The L-MBUS level converters are used to connect an M-Bus network to a L‑INX Automation Server, L‑ROC Room Controllers L‑GATE Gateway, or a LIOB‑586/587/588/589 I/O Controllers. Up to 20 or 80 M-Bus devices can be connected via L-MBUS20 or L-MBUS80.

TTL Connection

The TTL port is used to connect the L-MBUS to the EXT port of L -INX Automation Servers, L -ROC Room Controllers, and also to the L-GATE Gateways. The interface is galvanically isolated.

L-MBUS Level Converter Products

L-MBUS20

M-Bus level converter, interface for 20 M-Bus devices

L-MBUS80

M-Bus Level Converter, Interface for up to 80 M-Bus devices

L-CABLE1

Connection cable between LINX‑x0x or LINX‑x1x Automation Server and L-MBUSx0 M-Bus level converter

The post L-MBUS Level Converter appeared first on Kepler Electronics.

MP-Bus Interface

Maen Sirhan — Fri, 29 Mar 2024 08:31:39 +0000

The LMPBUS-804 connects up to four MP-Bus channels with up to 64 MP-Bus slaves to the USB port of the L‑INX Automation Server, L‑ROC Controller or L‑GATE Gateway Controller.

MP-Bus stands for Multi Point Bus. It is the Belimo Master/Slave bus system. The MP-Bus allows to connect up to 8 slaves to a master unit. By exclusively using latest design actuators (e.g. ..-MPL) it is possible to connect up to 16 slaves. The advantages of this bus include reduced wiring expenses and substantially higher functionality. Furthermore one sensor can be connected per MP-Bus slave. These sensors include active sensors, passive resistances sensors and switches. The sensor values can be read over the MP-Bus network.

MP-Bus Interface Products

LMPBUS-804

MP-Bus Interface for 16 devices per channel, up to 4 channels

The post MP-Bus Interface appeared first on Kepler Electronics.

NIC

Maen Sirhan — Fri, 29 Mar 2024 08:25:01 +0000

NIC Datasheet
NIC User Manual
Installation Instructions: NIC709-IPxE100C / NIC709-USB100
Certificates: EC
Downloads

LOYTEC NICs are the most universal network interfaces for CEA‑709 and IP-852 (Ethernet/‌IP) channels. Based on LOYTEC’s Core Technologies, they offer high packet rates and short response times. All NICs are fully compatible with products like NL220, ALEX, LonMaker®, and other LNS® applications. The NICs are also compatible with NodeUtil32, NLUtil, OPC servers, and high performance ORION applications.

The multiplexed network interface (MNI) support allows starting multiple LNS® or MIP applications to run in parallel with an LPA on a single network interface.

The built-in VPN function provides for simple VPN setup and secure access to remote sites. The LTE-800 interface enables wireless access to remote sites through a mobile carrier.

Features

Network interface for TP/FT‑10, TP/XF‑1250, RS485, and Ethernet/IP (IP‑852) channels
Available for USB and Ethernet port
Create up to eight network nodes with a single network interface (MNI devices)
Use the LPA, LSD Tool, your ORION applications, MIP applications, and LNS® (VNI) applications on a single network interface at the same time
Compatible with BMS e.g. Honeywell EBI, TAC VISTA, etc.
Compatible with LNS® applications in high performance VNI mode e.g. NL220, NLFacilities, NLOPC-VNI, ALEX, LonMaker®, etc.
Compatible with MIP applications (LDV interface) e.g. NodeUtil32, NLUtil, NLOPC-MIP, Honeywell CARE 5/7, etc.
Compatible with high performance ORION applications (ORION API)
NIC852 is fully compatible with L-IP and i.LON® 600 Internet routers
Use legacy MIP applications together with the IP‑852 (Ethernet) channel
With dual Ethernet, switched or separated (only NIC709‑IP3E100C, NIC709‑IP1E100C)
Supports WLAN with LWLAN‑800 Interface (only NIC709‑IP3E100C, NIC709‑IP1E100C)
Supports LTE with LTE‑800 Interface (only NIC709‑IP3E100C, NIC709‑IP1E100C)
Runs on Windows 10, Windows Server 2012, Windows Server 2016, Windows Server 2019

NIC Products

NIC709-USB100

USB-Interface, connects to the USB port of a PC, supports LonMark TP/FT-10, TP/XF-1250, and TP/RS-485

NIC709-IP1E100C

Remote network interface (RNI), PC connection via Ethernet/IP, Supports a LonMark TP/XF-1250 channel

NIC709-IP3E100C

Successor of NIC709-IP3E100, Remote network interface (RNI), PC connection via Ethernet/IP, Supports a LonMark TP/FT-10 channel

NIC852

Floating licence via USB hardlock key, uses Ethernet port of PC to connect to a LonMark IP-852 channel

NIC852-SW

Software license, Software activation with costs for one PC, uses Ethernet port of PC to connect to a LonMark IP-852 channel

LPOW-2415B

Power supply unit with power connector 24 VDC, 15 W

LWLAN-800

Wireless LAN Interface IEEE 802.11bgn

LT-03

Network terminator for 1 x TP/FT-10 or TP/LPT-10 (bus or free topology), 1 x Network Access Connector RJ45

LT-13

Network terminator for: 1 x TP/FT-10 or TP/LPT-10 (bus or free topology), 1 x TP/XF-1250 (bus toplogy only)

LT-33

Network terminator for 2 x TP/FT-10 or TP/LPT-10 (bus or free topology)

The post NIC appeared first on Kepler Electronics.

L-IP Router BACnet

Maen Sirhan — Fri, 29 Mar 2024 08:23:39 +0000

The LIP-ME201C, LIP-ME202C, and LIP-ME204C BACnet/‌IP Routers connect BACnet MS/‌TP channels to a BACnet/‌IP network. The BACnet routers are compliant with the standards ASHRAE 135‑2012 and ISO 16484‑5:2012. The routers can be configured to act as a BACnet Broadcast Management Device (BBMD). The L-IP BACnet/‌IP Routers also provide Foreign Device support and BACnet/SC.

The BACnet router can act as a BACnet Time Master and as a BACnet MS/‌TP Slave Proxy. Extended features like the optional write protection of the BDT, a BACnet/‌IP Access Control List (ACL), and a simple communications test for BBMD help to locate issues on the network. The BACnet router also features remote MS/‌TP data packet capturing. BACnet MS/‌TP data packets are captured by the device and can be analyzed using Wireshark (free Protocol Analyzer, www.wireshark.org). Wireshark can either connect to the L-IP online or the capture file is loaded from the L-IPs web server and analyzed offline in Wireshark.

The entire device configuration of the BACnet router is done via the built-in web server, optionally also secured via HTTPS protocol. The BACnet router is BTL tested and WSPcert certified as BACnet Application Specific Controller (B-ASC).

Each L-IP BACnet/‌IP Router is equipped with two Ethernet ports. It can either be configured to use the internal switch to interconnect the two ports or every port is configured to work in a separate IP network.

When the Ethernet ports are configured for two separate IP networks, one port can be connected for instance to a WAN (Wide Area Network) with enabled network security (HTTPS) and BACnet/SC while the second port can be configured to be connected to an insecure network (LAN) where the standard building automation protocols like BACnet/‌IP are present. These devices also feature firewall functionality of course to isolate particular protocols or services between the ports. The built-in VPN function provides for simple VPN setup and secure access to remote sites. The LTE-800 interface enables wireless access to remote sites through a mobile carrier.

Using the internal switch, a daisy chained line topology of up to 20 devices can be built, which reduces costs for network installation. The IP switch also allows the setup of a redundant Ethernet installation (ring topology), which increases reliability. The redundant Ethernet topology is enabled by the Rapid Spanning Tree Protocol (RSTP), which is supported by most managed switches.

Features

Routes packets between BACnet MS/‌TP and BACnet/‌IP, BACnet/SC
Compliant with ANSI/‌ASHRAE 135‑2012 and ISO 16484‑5:2012 standard
BBMD (BACnet Broadcast Management Device)
Foreign device support
Slave Proxy for up to 32 MS/‌TP slave devices
Configuration via built-in web server
Built-in OPC XML‑DA and OPC UA server
Dual switched or separated Ethernet ports
Access to network statistics via web browser
BACnet MS/‌TP diagnostic LED
BACnet MS/‌TP diagnostic via web interface
MS/‌TP remote data packet capture (Wireshark)
Ethernet link and activity LED
Secure web interface via HTTPS
128×64 graphic display with backlight
Local display of device information
Manual operation using the jog dial or VNC client
Supports WLAN through LWLAN‑800 Interface
Supports LTE through LTE‑800 Interface
Stores user-defined project documentation
Supports VPN for BACnet/IP

L-IP Router BACnet Products

LIP-ME201C

Successor of LIP-ME201, BACnet/IP Router, 1 x BACnet MS/TP (RS-485), 2 x Ethernet Port (BACnet/IP)

LIP-ME202C

BACnet/IP Router, 2 x BACnet MS/TP (RS-485), 2 x Ethernet Port (BACnet/IP)

LIP-ME204C

BACnet/IP Router, 4 x BACnet MS/TP (RS-485), 2 x Ethernet Port (BACnet/IP)

LPOW-2415B

Power supply unit with power connector 24 VDC, 15 W

LT-04

Network terminator for 1 x RS‑485 (bus topology, ANSI TIA/EIA-485), 1 x Network Access Connector RJ45

LT-B4

Network terminator, 1 x RS‑485 (bus topology, ANSI TIA/EIA-485) with biasing circuit (failsafe biasing)

The post L-IP Router BACnet appeared first on Kepler Electronics.

L-IP Router CEA-709

Maen Sirhan — Fri, 29 Mar 2024 08:22:07 +0000

LIP-xECTC Datasheet
Installation Instructions: LIP-3333ECTC, LIP-1ECTC / LIP-3ECTC / LIP-33ECTC
L-IP User Manual
Certificates: EC / UL
Downloads LIP-3333ECTC, LIP-1ECTC, LIP-3ECTC, LIP-33ECTC

The L-IP Routers LIP‑1ECTC, LIP‑3ECTC, LIP‑33ECTC, and LIP‑3333ECTC connect twisted pair channels (TP/‌FT‑10 or TP/‌XF‑1250) with the Ethernet/‌IP channel (IP‑852) in LonMark Systems. L-IP routes CEA‑709 packets through an IP based network such as a LAN (Ethernet), an Intranet, or even the Internet. In order to provide optimal router configurations, the L-IP is available in four different versions providing either 4 x TP/FT‑10, 2 x TP/FT‑10, 1 x TP/FT10, or 1 x TP/XF‑1250. Every L-IP supports the operating modes “Smart Switch Mode” and “Configured Router Mode”.

For an easy integration on the IP side, the L-IP provides a Web interface. On L-IP Routers LIP‑1ECTC, LIP‑3ECTC, LIP‑33ECTC, and LIP‑3333ECTC the Web interface can also be used via an encrypted HTTPS connection. Through this Web interface, the built-in CEA-852 Configuration Server can be switched on and configured. The Configuraton server is thus always available online in the network and no additional software tool is required.

Besides the router functionality, the L-IP Routers provide outstanding capabilities for network diagnostic and analysis. They allow the LPA (LOYTEC Protocol Analyzer) transparent access to the twisted pair channels (TP/‌FT-10 or TP/XF-1250) on the device via Ethernet/‌IP – via a local Intranet or the Internet. This allows a fast analysis of data communication and reduces time-consuming troubleshooting. All system registers are available as OPC XML‑DA and OPC UA data points.

The L-IP Routers LIP‑1ECTC, LIP‑3ECTC, LIP‑33ECTC, and LIP‑3333ECTC are equipped with two Ethernet ports. It can either be configured to use the internal switch to interconnect the two ports or every port is configured to work in a separate IP network.

When the Ethernet ports are configured for two separate IP networks, one port can be connected for instance to a WAN (Wide Area Network) with enabled network security (HTTPS) while the second port can be configured to be connected to an insecure network (building LAN) where the standard building automation protocols are present (e.g. IP-852). These devices also feature firewall functionality, of course to isolate particular protocols or services between the ports. The built-in VPN function provides for simple VPN setup and secure access to remote sites. The LTE-800 interface enables wireless access to remote sites through a mobile carrier.

Features

Routes CEA‑709 packets between TP/‌FT‑10 (link power compatible) or TP/‌XF‑1250 channels and Ethernet/‌IP (IP‑852)
Compliant with CEA-709, CEA-852, and ISO/‌IEC 14908-1 standard (LonMark System)
Supports Configured Router mode, Smart Switch mode, and Repeater mode
Built-in CEA-852 configuration server for up to 100 members
Support for operation behind NAT routers and firewalls
Easy installation, Auto-NAT, roaming, DHCP
Remote LPA support with LPA-IP
Integrated web server for device and IP-852 configuration
Built-in enhanced communication test for IP-852
Network diagnostic LEDs
Dual switched or separated Ethernet ports
Secure Web interface via HTTPS
Built-in OPC XML‑DA and OPC UA server
128×64 graphic display with backlight
Local display of device information
Manual operation using the jog dial or VNC client
Supports WLAN through LWLAN-800 Interface
Supports LTE through LTE‑800 Interface
Stores user-defined project documentation
Supports VPN for IP-852

L-IP Router CEA-709 Products

LIP-1ECTC

CEA-709/IP-852 Router, 1 x TP/XF-1250, 2 x Ethernet Port (IP-852)

LIP-3ECTC

Successor of LIP-3ECTB, CEA-709/IP-852 Router, 1 x TP/FT-10, 2 x Ethernet Port (IP-852)

LIP-33ECTC

Successor of LIP-33ECTB, CEA-709/IP-852 Router, 2 x TP/FT-10, 2 x Ethernet Port (IP-852)

LIP-3333ECTC

Successor of LIP-3333ECTB, CEA-709/IP-852 Router, 4 x TP/FT-10, 2 x Ethernet Port (IP-852)

LPOW-2415B

Power supply unit with power connector 24 VDC, 15 W

LWLAN-800

Wireless LAN Interface IEEE 802.11bgn

LT-03

Network terminator for 1 x TP/FT-10 or TP/LPT-10 (bus or free topology), 1 x Network Access Connector RJ45

LT-13

Network terminator for: 1 x TP/FT-10 or TP/LPT-10 (bus or free topology), 1 x TP/XF-1250 (bus toplogy only)

LT-33

Network terminator for 2 x TP/FT-10 or TP/LPT-10 (bus or free topology)

The post L-IP Router CEA-709 appeared first on Kepler Electronics.

LGATE-902

Maen Sirhan — Mon, 25 Mar 2024 14:09:19 +0000

The LGATE-902 Gateway is a powerful gateway that can host user specific graphical pages. The gateways provide connectivity functions to concurrently integrate CEA-709 (LonMark Systems), BACnet, KNX, Modbus, and M-Bus. Local operation and override is provided by the built-in jog dial and the backlit display (128×64 pixels). Device and data point information is provided by the Web interface and shown on the display via symbols and in text format.

LonMark Systems can be integrated via IP-852 (Ethernet/‌IP) or TP/‌FT‑10. LGATE-902 features an integrated Remote Network Interface (RNI) to access the TP/‌FT‑10 channel on the device via Ethernet/‌IP. BACnet integration is supported through BACnet/‌IP (Ethernet/‌IP), BACnet/SC or BACnet MS/‌TP (RS-485). LGATE-902 ist BACnet Building Controller (B-BC) BTL certified and can be configured to be a BBMD.

In addition, the gateway provides connectivity to KNXnet/‌IP and Modbus (RTU/ASCII, TCP, Master or Slave). M-Bus and KNX TP1 device integration needs optional interface modules.

Through the built-in web server, all data points can be monitored and changed. The gateway functionality allows data communication between all communication technologies available on the device. Different technology data points are mapped through Local Connections on the device. The mapping of different technology data points on distributed devices is supported by Global Connections. The gateway also support Smart Auto-Connect – the automatic generation of connections to substantially reduce engineering efforts and cost. Math objects allow to execute mathematical operations on data points. All technology data points are automatically created as OPC XML-DA and OPC UA data points.

The LGATE-902 Gateway is equipped with two Ethernet ports. It can either be configured to use the internal switch to interconnect the two ports or every port is configured to work in a separate IP network.

When the Ethernet ports are configured for two separate IP networks, one port can be connected for instance to a WAN (Wide Area Network) with enabled network security (HTTPS) while the second port can be configure to be connected to an insecure network (LAN) where the standard building automation protocols like BACnet/‌IP, LON/‌IP, or Modbus TCP are present. These devices also feature firewall functionality of course to isolate particular protocols or services between the ports. The built-in VPN function provides for simple VPN setup and secure access to remote sites. The LTE-800 interface enables wireless access to remote sites through a mobile carrier.

Using the internal switch, a daisy chained line topology of up to 20 devices can be built, which reduces costs for network installation. The IP switch also allow the setup of a redundant Ethernet installation (ring topology), which increases reliability. The redundant Ethernet topology is enabled by the Rapid Spanning Tree Protocol (RSTP), which is supported by most managed switches.

The L-GATE devices provide fully featured AST functionality (Alarming, Scheduling, and Trending) and can be integrated perfectly into the L-WEB System.

IoT Integration

The IoT function (Node.js) allows connecting the system to almost any cloud service, either for uploading historical data to analytics services, delivering alarm messages to alarm processing services or operating parts of the control system over a cloud service (e.g., scheduling based on Web calendars or booking systems). Processing Internet information such as weather data in forecast-based control is also possible. Finally, the JavaScript kernel also allows implementing serial protocols to non-standard equipment in primary plant control.

Features

Universal Gateway for BACnet, LonMark, KNX, Modbus, M-Bus, and EnOcean
Compliant with ANSI/ASHRAE–135‑2012 and ISO 16484‑5:2012 standard
B-BC (BACnet Building Controller) functionality, BTL certified
Supports BBMD (BACnet Broadcast Management Device)
Supports BACnet MS/TP, BACnet/IP or BACnet/SC
BACnet Client Function (Write Property, Read Property, COV Subscription)
BACnet Client Configuration with configuration tool (scan and EDE import)
Compliant with CEA‑709, CEA‑852, and ISO/‌IEC 14908 Standard (LonMark System)
Supports TP/‌FT‑10 or IP-852 (Ethernet/‌IP)
Support of dynamically created or static NVs
Support of user-defined NVs (UNVTs) and Configuration Properties (SCPTs, UCPTs)
Remote Network Interface (RNI) with 2 MNI devices
Direct connection to KNX/IP, KNX TP1 connection via LKNX-300 Interface
M-Bus Master according to EN 13757-3, connection via M-Bus Level Converter (LMBUS-20 or LMBUS-80)
Modbus TCP and Modbus RTU/ASCII (Master or Slave)
Automatic creation of Local Connections (Smart Auto Connect)
Math objects to execute mathematical operations on data points
Automatic mapping of network variables to BACnet objects in accordance with CEN/TS 15231:2005
Alarming, Scheduling, and Trending (AST)
Node.js support for easy IoT integration (e.g. Google
calendar, Alexa & friends, multimedia equipment,…)
Event-driven e-mail notification
Stores customized graphical pages
Visualization of customized graphical pages through LWEB‑900 and LWEB‑802/‌803
Built-in OPC XML-DA and OPC UA server
Dual switched or separated Ethernet ports
Access to network statistics
Integrated web server for device configuration and monitoring data points
Manual operation using the jog dial or VNC client
Local and remote access to information about device status and data points
128×64 graphic display with backlight
Configurable via Ethernet/‌IP or TP/FT‑10
Connection to EnOcean wireless devices via LENO-80x Interface
Supports SMI (Standard Motor Interface) through LSMI-80x
Supports WLAN through LWLAN-800 Interface
Supports MP-Bus through LMPBUS-804 Interface
Supports LTE through LTE-800 Interface
Stores user-defined project documentation

Tutorials

Features of L-INX 8.0 Release

This video presents several features of the new firmware.

Using EnOcean devices [G003]

This tutorial describes how to use EnOcean with LOYTEC devices.

How to create schedulers (CEA-709) [A001]

This tutorial describes how to create schedulers on an L-VIS Touch Panel with the configuration tool L-VIS Configurator.

How to create a calendar including exception days (CEA-709) [A002]

This tutorial describes how to create a calendar including exception days on an L-VIS Touch Panel with the configuration tool L-VIS Configurator.

How to operate a scheduler on the web interface of a L-INX Automation Server [A004]

This tutorial describes how to use the Web UI of the L-INX Automation Server.

How to create a remote scheduler (CEA-709) [A005]

This tutorial describes how to create a remote scheduler on the L-INX Automation Server with the configuration tool NL220 LonWorks© Manager.

How to create alarms (CEA-709) [A006]

This tutorial describes how to create alarms on the L-INX Automation Server with the configuration tool L-INX Configurator.

How to use e-mail configuration [A007]

This tutorial describes how to configure the L-INX Automation Server with the configuration tool L-INX Configurator.

How to create trend objects [A008]

This tutorial describes how to create trend objects on the L-INX Automation Server with the configuration tool L-INX Configurator.

How to create schedulers on BACnet devices [A201]

This tutorial describes how to create schedulers on BACnet devices on the L-INX Automation Server with the configuration tool L-INX Configurator.

How to create a calendar on BACnet devices [A202]

This tutorial describes how to create a calendar on the L-INX Automation Server with the configuration tool L-INX Configurator.

How to create a remote scheduler on BACnet devices [A205]

This tutorial describes how to create a remote scheduler on the L-INX Automation Server with the configuration tool L-INX Configurator.

How to create alarms on BACnet devices [A206]

This tutorial describes how to create alarms on the L-INX Automation Server with the configuration tool L-INX Configurator.

How to create static network variables [B001]

This tutorial describes how to create static network variables on the L-INX Automation Server with the configuration tool L-INX Configurator.

How to create dynamic network variables [B002]

This tutorial describes how to create dynamic network variables on the L-INX Automation Server with the configuration tool NL220 LonWorks© Manager.

How to create network variables by using LNS scan [B003]

This tutorial describes how to create network variables by using LNX scan on the L-INX Automation Server with the configuration tool L-INX Configurator.

How to create network variables by using network scan [B004]

This tutorial describes how to create network variables by using network scan on the L-INX Automation Server with the configuration tool L-INX Configurator.

How to import network variables by using CSV file import [B005]

This tutorial describes how to import network variables by using CSV file import on the L-INX Automation Server with the configuration tool L-INX Configurator.

How to import extern network variables (LNS scan or network scan) [B006]

This tutorial describes how to import extern network variables on the L-INX Automation Server with the configuration tool L-INX Configurator.

How to create network variables by using Filter Templates [B007]

This tutorial describes how to create network variables by using Filter Templates on the L-INX Automation Server with the configuration tool L-INX Configurator.

Manual creation of BACnet Server Objects [B201]

This tutorial describes how to create BACnet Server Objects manually on the L-INX Automation Server with the configuration tool L-INX Configurator.

How to create client mappings using network scan [B202]

This tutorial describes how to create client mappings using network scan on the L-INX Automation Server with the configuration tool L-INX Configurator.

How to create client mappings using EDE file import [B203]

This tutorial describes how to configure the L-INX Automation Server with the configuration tool L-INX Configurator.

A quick start scenario creating an L-WEB database [W002]

This tutorial describes how to create a database with the LWEB Server and the configuration tool L-INX Configurator on the example of configuring the L-INX Automation Server.

How to create automatic connections from CEA-709 to BACnet [G001]

This tutorial describes how to create automatic connections on the LGATE-900 Gateway with the configuration tool L-INX Configurator (former L-GATE Configurator).

How to create an L-GATE project from a predefined BACnet side [G002]

This tutorial describes how to create an L-GATE project from a predefined BACnet side on the LGATE-900 Gateway with the configuration tool L-INX Configurator (former L-GATE Configurator).

LGATE-902: Universal Gateway Products

LGATE-902

Universal Gateway

LPOW-2415A

LIOB-Connect Power Supply, 24 VDC, 15 W

LPOW-2415B

Power supply unit with power connector 24 VDC, 15 W

L-MBUS20

M-Bus level converter, interface for 20 M-Bus devices

L-MBUS80

M-Bus Level Converter, Interface for up to 80 M-Bus devices

LKNX-300

KNX interface to connect KNX TP1 devices

LENO-800

EnOcean Interface 868 MHz Europe

LENO-801

EnOcean Interface 902 MHz USA/Canada

LENO-802

EnOcean Interface 928 MHz Japan

LWLAN-800

Wireless LAN Interface IEEE 802.11bgn

LSMI-800

Standard Motor Interface for 16 motors via EXT port

LMPBUS-804

MP-Bus Interface for 16 devices per channel, up to 4 channels

LRS232-802

USB to 2x RS-232 Interface

The post LGATE-902 appeared first on Kepler Electronics.