LOYTEC Archives - Kepler Electronics

LOYCNV-PT1008 Voltage Converter

Maen Sirhan — Sun, 02 Jun 2024 17:38:13 +0000

The LOYCNV-PT1008 is a PT1000 to 0-10V interface containing eight channels for resistance to voltage conversion on devices with IOs or UIs (e.g. L-IOB, LROC-40x, …).

Features

PT1000 interface for L-IOB, LROC-40x, …
Converts up to eight PT1000 sensors in 2-wire connection (common GND)

LOYCNV-PT1008 Voltage Converter Products

LOYCNV-PT1008

8x PT1000 to 0-10 V converter (expected availability: Q3 2024)

The post LOYCNV-PT1008 Voltage Converter appeared first on Kepler Electronics.

L-Term Network Terminator (BACnet MS/TP, Modbus RTU or RS-485)

Maen Sirhan — Sun, 02 Jun 2024 17:07:38 +0000

LOYTEC offers network terminators for RS‑485 channels (ANSI TIA/‌EIA‑485) such as BACnet MS/‌TP, Modbus RTU, or TP/RS485 (CEA‑709) in DIN rail housings.

L-Term LT-04 is a terminator for RS‑485 channels. In addition, LT-04 comes with a network access connector (RJ45) for a simple and reliable connection to the network e.g. for maintenance or analyzing the network locally.

The LT-B4 is a bus terminator for an RS‑485 channel with biasing circuit (failsafe biasing). This biasing circuit draws the level of the bus during standby mode (idle) to a safe value (logic “1”). The LT-B4 needs a power supply of 24 V AC or 24 V DC.

L-Term Network Terminator (BACnet MS/TP, Modbus RTU or RS-485) Products

LT-04

Network terminator for 1 x RS‑485 (bus topology, ANSI TIA/EIA-485), 1 x Network Access Connector RJ45

LT-B4

Network terminator, 1 x RS‑485 (bus topology, ANSI TIA/EIA-485) with biasing circuit (failsafe biasing)

The post L-Term Network Terminator (BACnet MS/TP, Modbus RTU or RS-485) appeared first on Kepler Electronics.

LIOB-FT I/O Modules LonMark

Maen Sirhan — Tue, 02 Apr 2024 16:36:48 +0000

The LIOB-15x Modules are LonMark certified and communicate over TP/FT-10 in the LonMark System. They provide up to 512 address table entries (ECS mode) which eliminates all binding restrictions.

LIOB-FT Mode

The LIOB-15x Modules can be switched to LIOB-FT mode using manual local operation. In LIOB-FT mode, the LIOB-15x Modules extend L-INX Automation Servers and L-ROC Room Controllers with physical inputs and outputs via plug and play.

Local Operation and Override

All L-IOB I/O Modules are equipped with an LCD display (128×64) with backlight and jog dial for manual local operation. Device and data point information is displayed in text form and via graphical symbols.

Features

I/O module with physical inputs and outputs
SNVT-based interface for integration on the LonMark TP/FT-10 channel
LonMark certified
Manual operation using the jog dial
128×64 graphic display with backlight
Local access to information about device status and data points in clear text and symbols
Compliant with CEA‑709 and ISO/IEC 14908-2 standard (LonMark System)
Connected to the L-INX Automation Server or L-ROC Room Controller via LIOB‑FT
Automatic integration into device configurations with L-INX and L-ROC
Easy device replacement without any additional software
LNS plug‑in for the device configuration in the LonMark System

LIOB-FT I/O Modules LonMark Products

LIOB-150

LIOB-FT I/O Module: 8 UI, 2 DI, 2 AO, 8 DO (4 x Relay 6 A, 4 x Triac 0.5 A)

LIOB-151

LIOB-FT I/O Module: 8 UI, 12 DI

LIOB-152

LIOB-FT I/O Module: 6 UI, 6 AO, 8 DO (8 x Relay 6 A)

LIOB-153

LIOB-FT I/O Module: 6 UI, 6 AO, 5 DO (4 x Relay 16 A, 1 x Relay 6 A)

LIOB-154

LIOB-FT I/O Module: 7 UI, 4 AO, 7 DO (5 x Relay 6 A, 2 x Triac 0.5 A), 1 Pressure Sensor

LPOW-2415A

LIOB-Connect Power Supply, 24 VDC, 15 W

LPOW-2415B

Power supply unit with power connector 24 VDC, 15 W

L-TEMP2

External temperature sensor (NTC10K) for use with L-IOB Universal Inputs

The post LIOB-FT I/O Modules LonMark appeared first on Kepler Electronics.

L-STUDIO 3 Engineering Tool

Maen Sirhan — Tue, 02 Apr 2024 16:28:06 +0000

L‑STUDIO 3

L-STUDIO is the ultimate development and integration platform for programmable LOYTEC controllers, such as the L-INX automation servers, L-ROC room control system or programmable visualization solutions such as the LPAD-7. It combines the major building automation disciplines -programming, communication, and visualization – into a single tool. Together with the LWEB-900 building management system, it covers all phases of building automation, from prototyping to programming, configuration, and maintenance.

Achieving the highest levels of energy-efficiency and room comfort is only possible by forging all conventional controls into a single integrated building automation application. L-STUDIO helps to develop these applications in a timely and cost-effective manner. Template -based prototyping, reusable libraries and integrated testing tools support the project engineer’s efforts.

Programming

L-STUDIO speaks your language, ranging from the industry-proven PLC language IEC 61131 and its event-based successor IEC 61499 up to modern IoT applications using Node.js and Node-RED.

Using the cycle-based IEC 61131 language, classic applications such as boiler plants, air handling units or heating/cooling circuits can be easily automated. The LOYTEC building automation library already contains many sample applications that can be used as a starting point for your application.

Room control applications can be implemented using the LOYTEC L -ROC room automation library. It provides an integrated solution for HVAC, lighting, and sunblinds solution as well as many other functions required in the modern living space. The room automation library uses the IEC 61499 event -based language to create low -latency and fully networked applications that eliminate the need for classical network integration.

Communication

In L-STUDIO logic blocks, called CATs, can contain technology objects, such as BACnet objects or OPC tags as templates. Data points are then automatically created when a CAT is instantiated on a device. This makes the creating of network interfaces of different technologies almost automatic. A CAT can also contain technology level objects, such as alarms, schedules or trends which are also automatically instantiated and linked to the logic program. The L-STUDIO CATs support all LINX automation server technologies: BACnet, OPC XML/DA, Bluetooth, DALI, EnOcean, SMI, CEA -709, KNX, Modbus, M -Bus and will support future technologies yet to come.

State-of-the-art buildings require Internet of Things services, such as public trans ‑ port information, office booking systems or building information systems. These can be integrated using Node.js or Node-RED. Their integration allows classical PLC programming to be combined with latest web technologies.

Visualization

L-STUDIO CATs can also contain graphical symbols. These visualize the data points of the CAT and represent the logic object in a graphical way, such as a pump diagram, a room overview, or an entire plant display.

These symbols can be combined into graphical projects that can be used on L -VIS or L -PAD devices. The graphical projects can also be used on a PC with LWEB 802/803 or on mobile devices using the LWEB-APP. All visualizations are fully editable by the user and support all features of the L -VIS technology.

Management

L-STUDIO projects can be imported into LWEB -900. All devices and graphical views are imported automatically. The parameter views of LWEB -900 allow to configure and optimize the devices that have been created by L-STUDIO. The graphical views can be used in LWEB-900 together with the access control functions to provide the building maintainers and end-users with a secure and consistent interface to the building.

L-STUDIO provides documentation and versioning features to keep track of the project. All library blocks can be documented in HTML-style. Libraries can also be versioned, distributed in binary form or managed in a source versioning tool to track and document changes.

L-STUDIO 3 Engineering Tool Products

L-STUDIO

Device configuration and programming suite

LTRAIN-LSTUDIO

L-STUDIO Training (2 days)

The post L-STUDIO 3 Engineering Tool appeared first on Kepler Electronics.

L-ACT Actuators

Maen Sirhan — Tue, 02 Apr 2024 16:24:38 +0000

Features

Air damper size up to approximately 1 m², 10.76 ft ²
Torque motor 5 Nm, 45in-lb
Nominal voltage AC/DC 24 V
Communication via Belimo MP-Bus

L-ACT Actuators

L-ACT101-MP

Actuator 5/8‘‘, 5Nm, MP-Bus cable

L-ACT102-MP

Actuator 3/4‘‘, 5Nm, MP-Bus cable

L-ACT-FRAME1

L-IOB I/O Controller: 6 UI, 2 AO, 5 DO (5 x Triac 0.5 A), 1 Pressure Sensor

LIOB-585

L-IOB I/O Controller: 6 UI, 2 AO, 5 DO (5 x Triac 0.5 A), 1 Pressure Sensor

The post L-ACT Actuators appeared first on Kepler Electronics.

DVS-110W02-3SFP Managed Industrial Ethernet Switch

Maen Sirhan — Tue, 02 Apr 2024 16:20:32 +0000

DVS-110W02-3SFP Datasheet
DVS-110W02-3SFP Installation Instructions
Certificates: EC / UL
Downloads

The DVS‑110W02‑3SFP Managed 10‑Port Ethernet Switch provides many essential features. Its enhanced hardware design, the user‑friendly software interface, the packet protection and compatibility with multiple industrial communication standards makes it a highly reliable active network component.

The DVS‑110W02‑3SFP provides two built-in redundant power supplies and together with its RSTP support it is the perfect fit for building up highly available Ethernet ring topologies for L-INX, L-IOB, and L-ROC controller.

It features a wide operating temperature range from ‑40°C to 75°C, and it is UL, CE, and FCC certified.

Features

IPv6 Network address for larger network and neighbor discovery
Automatic IP assignment by DHCP/BootP server for easy network construction
DHCP relay option 82 for sending DHCP requests with clients’ identities to a DHCP server
SNMP v1/v2c/v3 facilitates the exchange of management between network devices
Support MODBUS TCP protocol that facilitates the remote management by SCADA and other industrial devices
STP/RSTP/MSTP for network redundancy further ensures reliability
QoS(IEEE 802.1p) and TOS/DSCP for mission-critical applications
IEEE 802.1Q VLAN, Port-based VLAN and GVRP to optimize network strategy
SNTP (simple network time protocol) for network clock synchronization
Broadcast/Multicast/Unknown Unicast storm control improves throughput problems
MAC addresses locking function per port blocks unauthorized access
USB console interface for easy connection with laptops
IGMP Snooping and GMVP prunes multicast traffic
CPU utilization displays the amount of works the CPU handles
DDM diagnosis function by SFP fiber module
Auto warning by email, DI, relay, Syslog & SNMP trap
Compatible with various industrial protocols, EtherNet/IP, Profinet, CC-LINK IE and DNP 3.0

DVS-110W02-3SFP Managed Industrial Ethernet Switch

LOYDVS-110W02-3SFP

Managed 10-Port Fast Ethernet Switch

LOYDVS008I00

Unmanaged 8-Port Fast Ethernet Switch

The post DVS-110W02-3SFP Managed Industrial Ethernet Switch appeared first on Kepler Electronics.

DVS-008I00 Unmanaged Fast Ethernet Switch

Maen Sirhan — Tue, 02 Apr 2024 16:19:35 +0000

The DVS‑008I00 is an unmanaged 8‑Port Fast Ethernet Switch with enhanced hardware design, packet protection and compatibility with multiple industrial communication standards.

The DVS‑008I00 features wide operating temperature range from ‑40°C to 75°C, and it is UL, CE, and FCC certified.

Features

12 to 48 VDC terminal block power input
Compatible with various industrial protocols of EtherNet/IP, Profinet, CC-LINK IE and DNP 3.0

DVS-008I00 Unmanaged Fast Ethernet Switch

LOYDVS008I00

Unmanaged 8-Port Fast Ethernet Switch

LOYDVS-110W02-3SFP

Managed 10-Port Fast Ethernet Switch

The post DVS-008I00 Unmanaged Fast Ethernet Switch appeared first on Kepler Electronics.

LOYRTU-485 Modbus Remote I/O Communication Module

Maen Sirhan — Tue, 02 Apr 2024 16:15:32 +0000

The LOYRTU-485 is a Modbus remote I/O communication module to remote-control Slim series DI/DO and AI/AO extension units. The RTU-485 is a standard Modbus slave compatible with LOYTEC devices featuring a Modbus Interface supporting Modbus master mode.

The LOYRTU-485 is UL, CE, and FCC certified.

Features

Supports Modbus protocol, slave mode
Connects up to 8 DVP-S series I/O modules
Max. baudrate: 115.2k bpsk

LOYRTU-485 Modbus Remote I/O Communication Module Products

LOYRTU-485

Modbus Remote I/O Communication Module

The post LOYRTU-485 Modbus Remote I/O Communication Module appeared first on Kepler Electronics.

LBOX-600 System Distribution Box

Maen Sirhan — Tue, 02 Apr 2024 16:11:19 +0000

With L-BOX System Distribution Boxes, LOYTEC offers the possibility of a decentralized installation of hardware components, e.g. for the flexible room automation system L-ROC.

For the typical requirements of room automation projects with reoccurring segments, the hardware designed for a certain amount of segments (e.g. 8 or 16 segments, usually I/O modules) can be installed in L-BOX. L-BOX is normally mounted in an intermediate ceiling or double floor. The cabling of the field components in the segment (sunblind motor, actuators for valves, window contacts etc.) can be connected to the L-BOX in a star topology. In the L-BOX, the cables are strain-relieved and directly wired to the I/O modules.

LBOX-600 System Distribution Box Products

LBOX-600

L-BOX System Distribution Box for room automation components, 600 x 250 x 82 (L x W x H in mm)

The post LBOX-600 System Distribution Box appeared first on Kepler Electronics.

L-POW Power Supply

Maen Sirhan — Tue, 02 Apr 2024 16:09:54 +0000

LPOW-2415x/2460B Datasheet
LOYTEC Device User Manual
Installation Instructions: LPOW-2415A / LPOW-2415B / LPOW-2460B
Certificates: EC / UL
Downloads: LPOW-2415A / LPOW-2415B / LPOW-2460B

LPOW-2415A

LPOW-2415A is used to supply power to LOYTEC devices with the LOYTEC LIOB‑Connect side outlet such as the L-INX Automation Servers, L-ROC Room Controller, L-GATE Universal Gateways and LIP-ME204. In addition, L-IOB I/O Modules and Controllers (except LIOB-585) can be powered by the LPOW-2415A.

LPOW-2415B

The power supply LPOW-2415B provides 24 V DC via a plug-in screw terminal. It is used to supply power to LOYTEC devices with a separate power terminal of 24 V DC.

Energy -Efficient

The LPOW-2415 are highly efficient switching power supplies. Their efficiency is approximately 80 %. The input voltage range of 85–240 V AC (50–60 Hz) allows worldwide use.

LPOW-2460B

The LPOW‑2460B power supply provides 24 V DC and maximum 60 W with screw terminals. It is used to supply power to LOYTEC devices with a separate power terminal of 24 V DC.

L-POW Power Supply Products

LPOW-2415A

LIOB-Connect Power Supply, 24 VDC, 15 W

LPOW-2415B

Power supply unit with power connector 24 VDC, 15 W

LPOW-2460B

Power supply unit with power connector 24 V DC, 60 W

The post L-POW Power Supply appeared first on Kepler Electronics.

L-Term Network Terminator (TP/FT-10 and TP/XF-1250)

Maen Sirhan — Tue, 02 Apr 2024 16:09:12 +0000

LOYTEC offers several network terminators in DIN rail housing for the LonMark TP/FT-10 and TP/XF-1250 channels.
L-Term LT-03 offers one standard network terminator for a TP/FT-10 or TP/LPT-10 channel supporting bus and free topology. In addition, LT-03 comes with a network access connector (RJ45) for a simple and reliable connection to the CEA‑709 network e.g. for maintenance or analyzing the network locally.
L-Term LT-33 offers two standard network terminators for TP/FT-10 or TP/LPT‑10 channels in bus and free topology. LT-33 is the perfect solution for LOYTEC network infrastructure products (e.g. L-IP, L-Switch^XP, L-Proxy etc.).
L-Term LT-13 combines a terminator for a TP/FT-10 or TP/LPT-10 channel in bus or free topology with a terminator for a TP/XF-1250 channel. LT-13 is the perfect solution to be used together with the LS-13CB, LS-13300CB, or the LS-13333CB L-Switch^XP.

L-Term Network Terminator (TP/FT-10 and TP/XF-1250) Products

LT-03

Network terminator for 1 x TP/FT-10 or TP/LPT-10 (bus or free topology), 1 x Network Access Connector RJ45

LT-13

Network terminator for: 1 x TP/FT-10 or TP/LPT-10 (bus or free topology), 1 x TP/XF-1250 (bus toplogy only)

LT-33

Network terminator for 2 x TP/FT-10 or TP/LPT-10 (bus or free topology)

The post L-Term Network Terminator (TP/FT-10 and TP/XF-1250) appeared first on Kepler Electronics.

LOYUNO-L UNOlite Indoor Air Quality Sensor

Maen Sirhan — Tue, 02 Apr 2024 16:02:55 +0000

LOYUNO-L represents the pinnacle of indoor air quality monitoring, purposefully designed for effortless integration with BAS/BMS systems. This advanced instrument detects and analyses a wide range of indoor air quality factors, including Ultra-fine, Fine, and Standard Suspended Particulates (PM1, PM2.5, and PM10), Carbon Dioxide (CO₂), Total Volatile Organic Compounds (TVOC), while also monitoring Temperature and Humidity levels.

LOYUNO-L ensures accurate data, serving as a vital component in achieving LEED green or WELL certification for your building. Rigorously tested and certified for its precise sensing capabilities in detecting PM2.5, CO₂, and TVOC, LOYUNO-L meets the stringent standards set by WELL v2.

LOYUNO-L comes equipped with LOYTEC Bluetooth Mesh capabilities, seamlessly integrating with the other Bluetooth Mesh enabled devices. This versatile compatibility makes LOYUNO-L equally well-suited for both new construction projects and retrofitting BAS/BMS systems.

Features

Multiple IAQ monitors (PM1, PM2.5, PM10, CO₂, TVOC, Temperature, Humidity)
Supports BACnet MS/TP and Modbus RTU
Meets Q1 2022, v2 WELL A08 Requirements
Bluetooth Mesh based sensor
LEDs for optical air quality feedback and status indication
Easy integration on Bluetooth Mesh enabled LOYTEC devices (e.g. LPAD-7)
RESET Grade B Accredited Monitor

LOYUNO-L UNOlite Indoor Air Quality Sensor Products

LOYUNO-L

UNOlite Indoor Air Quality Sensor

The post LOYUNO-L UNOlite Indoor Air Quality Sensor appeared first on Kepler Electronics.