LDALI Archives - Kepler Electronics

L-RC1 Infrared Remote Control

Maen Sirhan — Tue, 02 Apr 2024 15:50:39 +0000

The L-RC1 is an infrared remote control, optimized for room automation applications. It allows the control of the room’s lights, sunblinds and HVAC system.

It supports the individual control for up to two channels – groups of luminaires and blinds – and scene control for up to three scenes.

For HVAC applications the temperature setpoint and fan speed can be adjusted, A/C can be switched on and off and the room’s occupancy status can be changed.

The L-RC1 is designed to work with L-DALI multi-sensors (LDALI-MSx-BT) and L-STAT room operation panels.

Features

Infrared remote control optimized for room automation applications
Control up to two light channels
Control up to two sunblind channels
Scene control for up to three scenes
Adjust temperature setpoint
Adjust fan speed
Set occupancy status
Switch A/C on/off

L-RC1 Infrared Remote Control Products

L-RC1

Infrared remote control for room automation applications

The post L-RC1 Infrared Remote Control appeared first on Kepler Electronics.

LDALI-PWR2-U / LDALI-PWR4-U Power Supply

Maen Sirhan — Tue, 02 Apr 2024 15:49:36 +0000

L-FOCUS: L-DALI Lighting Control Solutions (English)
LDALI-PWRx-U Datasheet
L-DALI User Manual
LDALI-PWRx-U Installation Instructions
Certificates: EC / DALI-2 / UL
Downloads

The DALI-2 power supplies LDALI-PWR2-U and LDALI-PWR4-U are used to power two or four DALI channels. Per channel, the power supplies provide a guaranteed supply current of 116 mA to power devices connected to the DALI channel.

In case the DALI devices connected to the channel consume more than the 116 mA, two DALI outputs of the power supplies can be used in parallel, resulting in a guaranteed supply current of 232 mA (maximum supply current of 250 mA).

Installation

The DALI channel is treated to be non-SELV (Safety Extra Low Voltage). Therefore, the relevant installation regulations for low voltage apply. The cable of a DALI channel is either limited to a maximum length of 300 m using a minimum wire cross-section of 1.5 mm² (AWG15) or must ensure a maximal voltage drop of 2 V.

Wide Range Supply Voltage

The power supplies accept a wide range of supply voltage from 85-240 V AC, 50/‌60 Hz. They also feature a starting-current limitation.

DALI Power Outputs

The DALI power outputs provide 18 V (11 V – 20.5 V) and 116 mA. The power outputs are isolated from mains by reinforced insulation. The power outputs are short circuit proof and shut down if thermally overloaded. When a thermal overload occurs, the DALI control lamp switches off.
The LDALI-PWR2-U and LDALI-PWR4-U are DALI-2 certified.

LDALI-PWR2-U / LDALI-PWR4-U Power Supplies Products

LDALI-PWR2-U

DALI-2 power supply, 85-240 V, 50/60 Hz, Output: 2 x 16 VDC, 116 mA (DALI bus)

LDALI-PWR4-U

DALI-2 power supply, 85-240 V, 50/60 Hz, Output: 4 x 16 VDC, 116 mA (DALI bus)

The post LDALI-PWR2-U / LDALI-PWR4-U Power Supply appeared first on Kepler Electronics.

L-DALI: Pushbutton Coupler

Maen Sirhan — Tue, 02 Apr 2024 15:48:43 +0000

L-FOCUS: L-DALI Lighting Control Solutions (English)
LDALI-BM2 Datasheet
L-DALI User Manual
LDALI-BM2 Installation Instructions
Certificates: EC / DALI-2
Downloads

The LDALI‑BM2 pushbutton coupler integrates up to four customary light push buttons and switches into a DALI channel. Alternatively, two of the four inputs can be used as analog inputs to connect devices like sliders, dials or even resistance based sensors like NTC temperature sensors.

Connected pushbuttons or switches can be used to control luminaires and sunblinds using L-DALI lighting controllers or L-ROC room automation controllers. The following functions are available:

Dim up, dim down
Off
On with last dimming value
Scene recall: 1–15
Dim to a specified value in %
Color temperature warmer/colder
Activate auto mode
Move Sunblind up/down
Set area Occupied/Unoccupied

In the mode toggle, the function is carried out depending on the lighting status (toggle switch). Communication and power supply is handled via the DALI bus. The LDALI-BM2 is a DALI-2 certified input device as defined in the IEC 62386 2014 standard and can be integrated into DALI-2 systems of other vendors.

Features

Easy integration into LOYTEC L‑DALI lighting systems and LROC‑40x room automation controllers
DALI-2 certified input device as defined in IEC 62386 2014 standard
2 digital inputs (dry contact) for conventional pushbuttons or switches
2 universal inputs (potential free) for conventional pushbuttons, switches, sliders, dials or NTC temperature sensors
4 outputs for direct control of feedback LEDs
Multi‑master compatible, up to 64 LDALI‑BM2 pushbutton couplers per DALI channel with sufficient dimensioned bus supply
Supplied via the DALI channel, no external power supply is necessary
Pre-confectioned wires for connection of inputs
Optimized for mounting behind standard switches

L-DALI: Pushbutton Coupler Products

LDALI-BM2

Quadruple DALI pushbutton coupler

The post L-DALI: Pushbutton Coupler appeared first on Kepler Electronics.

LDALI-PWR1-U Power Supply

Maen Sirhan — Tue, 02 Apr 2024 15:47:49 +0000

L-FOCUS: L-DALI Lighting Control Solutions (English)
LDALI-PWR1-U Datasheet
L-DALI User Manual
LDALI-PWR1-U Installation Instructions
Certificates: EC / DALI-2
Downloads

The LDALI‑PWR1‑U is a DALI power supply for one channel with a guaranteed supply current of 50 mA (maximum supply current of 62 mA).

It is well suited as supply for small standalone DALI‑systems with a limited amount of DALI‑components or even for luminaire integration. A typical LOYTEC application is the supply of a DALI subsystem in a BT‑mesh ecosystem (e.g. for a room), in which the sensor acts as DALI application controller and gateway to the mesh ecosystem. However, the LDALI‑PWR1‑U can also be used only to supply the LOYBT-MSx Bluetooth multisensors.

In applications with higher DALI currents up to 4 LDALI‑PWR1‑U can be used in parallel, resulting in a guaranteed supply current of 200 mA (maximum supply current of 248 mA).

Installation

The DALI channel is treated to be non‑SELV (Safety Extra Low Voltage). Therefore the relevant installation regulations for low voltage apply. The cable of a DALI channel is either limited to a maximum length of 300 m using a minimum wire cross‑section of 1.5 mm² (AWG15) or must ensure a maximal voltage drop of 2 V.

Wide Range Supply Voltage

The power supply accepts a wide range of supply voltage from 85–240 V AC, 50/ 60 Hz, and also features a starting‑current limitation.

DALI Power Output

The DALI power output provides 16 V (11 V – 20.5 V) and 50 mA guaranteed supply current. The power output is isolated from mains by reinforced insulation. The power output is short circuit proof and shuts down if thermally overloaded.

The LDALI‑PWR1‑U is DALI‑2 certified.

LDALI-PWR1-U Power Supply Products

LDALI-PWR1-U

DALI Power Supply for 1 DALI channel, 50mA

DALI-2

The post LDALI-PWR1-U Power Supply appeared first on Kepler Electronics.

LDALI-RM8 Relay Module

Maen Sirhan — Tue, 02 Apr 2024 15:46:15 +0000

L-FOCUS: L-DALI Lighting Control Solutions (English)
LDALI-RM8 Datasheet
L-DALI User Manual
LDALI-RM8 Installation Instructions
Certificates: EC / DALI-2 / UL
Downloads

The LDALI-RM8 Relay Module enables the control of standard loads via DALI. Typical application scenarios are the integration of non‑DALI luminaires or other loads like fans in toilets or washrooms, motors for partition walls or screens and fire protection flaps in DALI lighting applications. The device provides 8 built-in relay contacts, which can be controlled individually via separate DALI addresses as long as the corresponding digital input is open. Closing this input will always switch on the relay (override). Each relay provides a switch that indicates the state and that can be used to switch the relay manually (installation and maintenance). The built-in relay contacts can be used for currents of up to 16 A. They support a wide voltage range of 120 – 277 V AC and up to 30 V DC. The relays are suitable for loads with high inrush currents.

Together with the LOYTEC L-DALI controllers or LROC‑40x room automation controllers, the LDALI-RM8 devices act as programmable switching output modules. The integration of the module in the DALI network follows the same simple steps as the integration of DALI lamps. The device supports the DALI specification IEC 62386‑208 (Device Type 7, “switching function”) for non‑dimmable loads. The LDALI‑RM8 is externally powered either by 24 V DC or 85 – 240 V AC.

As a unique safety feature, the relay state for fault conditions can be partially configured. In case of a power loss on the DALI bus, the relays will switch to the position as defined with the DALI configuration register “System Failure Level”. In case of a power loss on the 24 V DC / 85 – 240 V AC the relays keep their state until a “Power On” occurs, at which they will switch to the state defined in the “Power On Level” configuration register.

The LDALI-RM8 is intended to be used in a switching cabinet.

The LDALI-RM8 is DALI-2 certified.

Features

Easy integration into LOYTEC L‑DALI lighting systems and LROC‑40x room automation controllers
Device configuration with the free LINX-Configurator or via the built‑in web server of the L‑DALI controller
Programmable switching outputs for standard loads in the power grid
Relay contact switching voltage: 120 – 277 V AC
Suitable for loads with high inrush currents
Up to 8 LDALI‑RM8 modules per DALI channel
Supplied via 85 – 240 V AC or 24 V DC ±10 %
Potential‑free, bi‑stable relay make contact
Relay contacts connectable with different phases
DALI specification IEC 62386‑208 (Device Type 7 – Switching Function) supported
DALI-2 certified
Configurable relay positions in case of DALI line outage
Relays keep their state in case of power loss
Manual switches on device for indication and manual override
Digital inputs forcing the corresponding relays to switch on (override, status can be queried)
Firmware update over DALI

LDALI-RM8 Relay Module Products

LDALI-RM8

DALI Relay Modul, 8 channel

DALI-2

The post LDALI-RM8 Relay Module appeared first on Kepler Electronics.

LDALI-MS Multi-Sensor

Maen Sirhan — Tue, 02 Apr 2024 15:41:57 +0000

LDALI-MS2-BT / LDALI-MS3-BT / LDALI-MS4-BT Multi-Sensor

LDALI-MS3-BT

LDALI-MS4-BT

The LOYTEC LDALI-MS2-BT/MS3-BT/MS4-BT multi‑sensor performs occupancy detection and measures the illuminance level. It integrates perfectly into the L‑DALI product line of lighting controllers and LROC‑40x room automation controllers. The occupancy sensor uses a passive infrared presence detector and a digital microphone. The sensor is optimized for use in typical office environments where even the small movements of somebody working at a desk and hitting the keyboard have to be detected across the complete detection area.

The LDALI-MS2-BT/MS3-BT provides a presence detection zone diameter of 10.8 m at 3 m mounting height and is ideal to cover a typical office room or an area in an open office space. As well it is suitable for highbay‑applications for mounting heights up to 12 m. The detection area for mounting heights from 5 m to 12 m is 256 m2.

The LDALI-MS4-BT provides a flat lense and the presence detection zone diameter is 7 m at 3 m mounting height.

With the built‑in infrared receiver, the room’s lights, sunblinds and HVAC system can be controlled via the optionally available IR remote control L-RC1. In addition to occupancy and illuminance sensors, the LDALI-MS2-BT/MS3-BT/MS4-BT comes with integrated temperature and humidity sensors. In room automation applications, those values can used to calculate the current dew point. On the back of the sensor, there is a connector for three digital inputs, allowing to connect conventional switches and push‑buttons, window contacts, dew point sensor, etc. This feature not only saves on additional hardware, but also significantly reduces wiring costs, as the inputs can be wired inside the room and wires no longer have to be pulled to the I/O modules in the switching cabinet.

Furthermore, the LDALI-MS2-BT/MS3-BT/MS4-BT can transmit all supported beacon types (iBeacon, Eddystone UID beacon or manufacturer specific LOYTEC beacon) for indoor localization.

The LDALI-MS2-BT comes with three mounting options: It can be mounted in‑wall in standard flush‑mounted boxes, spring snap in false ceilings and on‑wall with the included surface mounting box. The LDALI-MS3-BT/MS4-BT is designed to be used with spring snaps in false ceilings.

Communication and power supply is handled via the DALI bus. The LDALI-MS2-BT/MS3-BT/MS4-BT is a DALI-2 certified multi‑sensor as defined in the IEC 62386 (2014) standard and can integrated into DALI‑2 systems of other vendors.

Features

Easy integration into LOYTEC L‑DALI lighting systems and LROC‑40x room automation controllers with a special focus on lighting control and reducing energy costs
DALI-2 certified input device, according to IEC 62386-101, IEC 62386-103, IEC 62386-301, IEC 62386-303 and IEC 62386-304
High sensitivity occupancy detection – dual technology (PIR and acoustic, separate sensitivity parameter for each technology, sensitivity adjustable), optimized for office applications
Lux level measurements
Built-in infrared receiver for optional infrared remote control L-RC1
Temperature sensor
Humidity sensor
3 digital inputs (dry contact)
Configurable Bluetooth beacons and services: indoor navigation, asset tracking and access to LWEB-900 room control solution
The LDALI-MS3/MS4-BT can mounted directly in false ceilings (spring mount included).
The LDALI‑MS2-BT can mounted in a flush-mounted box, directly in false ceilings (spring mount included) or on-wall (mounting kit LOYMS2-OW must ordered separately).
Multi-master compatible, up to 16 LDALI-MS2-BT/MS3-BT/MS4-BT sensors per DALI channel given a sufficiently dimensioned bus supply
Supplied via the DALI bus, no external power supply required
Sensor head of the LDALI-MS2-BT/MS3-BT can tilted up to ±15° vertically
Flat lense in LDALI-MS4-BT type
Firmware update via DALI

LDALI-MS2-BT / LDALI-MS3-BT / LDALI-MS4-BT Multi-Sensors Products

LDALI-MS2-BT

DALI-2 multi-sensor (presence detection, illuminance sensor, IR receiver, temperature sensor, humidity sensor, 3 digital inputs, Bluetooth), up to 12 m mounting height

LDALI-MS3-BT

DALI-2 multi-sensor (presence detection, illuminance sensor, IR receiver, temperature sensor, humidity sensor, 3 digital inputs, Bluetooth), up to 12 m mounting height

LDALI-MS4-BT

DALI-2 multi-sensor (presence detection, illuminance sensor, IR receiver, temperature sensor, humidity sensor, 3 digital inputs, Bluetooth, flat lens), up to 5 m mounting height

LOYMS2-OW

LOYMS2-OW, On-wall Surface Mounting Box Kit for LDALI-MS2-BT / LOYBT-MS2 (8 boxes per package), expected availability Q2 2024

L-RC1

Infrared remote control for room automation applications

The post LDALI-MS Multi-Sensor appeared first on Kepler Electronics.

LDALI-PD1 Phase-Cut Dimmer Module

Maen Sirhan — Tue, 02 Apr 2024 15:20:02 +0000

L-FOCUS: L-DALI Lighting Control Solutions (English)
LDALI-PD1 Datasheet
L-DALI User Manual
LDALI-PD1 Installation Instructions
Certificates: EC / DALI-2
Downloads

The LDALI‑PD1 module enables the control of phase‑cut dimmed consumers via a DALI channel. Typical application scenarios are the integration of 230V LED-retrofit‑bulbs or halogen lamps in DALI lighting applications.

The device supports a wide voltage range from 220‑240 V AC 50/60Hz. The LDALI‑PD1 is suitable for loads from 1VA up to 150VA. The load type (RL/RC) is automatically detected and used to select a suitable dimming‑method (leading or trailing edge phase‑cut). The dimming range is 3%‑100%.

The integration of the module in the DALI network follows the same simple steps as the integration of a DALI lamp. The device supports the DALI‑specification IEC 62386‑205 (Device Type 4, “Incandescent lamp”). The LDALI‑PD1 modules are directly connected to a DALI‑channel and also supplied with energy by that channel. Thus in case of a system failure the intended state of the output is off.

The LDALI‑PD1 is equipped with an open‑circuit detection that indicates a lamp failure if no load is connected.

The LDALI‑PD1 is designed for installation in distribution boxes or behind standard plugs in installation boxes.

Features

Easy integration into LOYTEC L-DALI lighting system and LROC-40x room automation controllers
Device configuration with the free LINX Configurator or via the built-in web server of the L-DALI controller
Dimmable built-in phase-cut dimmer
Automatic load detection and selection of leading or trailing edge phase-cut dimming
Suitable for phase-cut dimmed consumers like dimmable retrofit LED and CFL lamps, halogen lamps, …
Wide range voltage support (220‑240 V AC 50/60Hz)
Up to 64 LDALI‑PD1 modules per DALI channel with sufficient dimensioned bus supply
Supplied via DALI channel
Electrically isolated between DALI and mains
Open circuit detection
DALI specification IEC 62386‑102 and IEC 62386‑205 supported
Firmware update via DALI

LDALI-PD1 Phase-Cut Dimmer Module Products

LDALI-PD1

DALI Phase-Cut Dimmer Module

DALI-2

The post LDALI-PD1 Phase-Cut Dimmer Module appeared first on Kepler Electronics.

LDALI-PWM4 PWM Modules

Maen Sirhan — Tue, 02 Apr 2024 15:17:53 +0000

L-FOCUS: L-DALI Lighting Control Solutions (English)
LDALI-PWM4 Datasheet
L-DALI User Manual
LDALI-PWM4/RGBW/TC Installation Instructions
Certificates: EC / DALI-2
Download

The LDALI-PWM4-x is a 4 channel constant voltage LED driver. It is suitable for constant voltage LED modules and LED strips with operating voltages from 12 to 24 V DC.

The module provides a wide dimming range from 0.1% to 100% and adjustable PWM frequency (125/250/500 Hz). The maximum load is limited by 3 A per channel. The module provides overtemperature protection as well as open- and short-circuit-protection for each channel.

From a DALI perspective, the channels can be controlled independently via separate DALI addresses. The LDALI-PWM4 module is compliant to the DALI specifications IEC 62386-101, IEC 62386-102 and IEC 62386-207 (Device Type 6,“LED”). Separate module types for tunable white (LDALI-PWM4-TC) and colour control applications (LDALI-PWM4-RGBW) support the DALI specification IEC 62386-209 (Device Type 8, “Colour Control”).

Features

Easy integration into LOYTEC L-DALI lighting systems and LROC-40x room automation controllers
Device configuration with the free LINX Configurator or via the built-in web server of the L-DALI controller
Dimmable built-in constant voltage DALI LED driver
Suitable for constant voltage LED modules and LED strips
LDALI-PWM4: 4 PWM channels, each of which can be controlled independently via separate DALI addresses
LDALI-PWM4-TC: 4 PWM channels, 2 of which are controlled via a DALI address (DT8 – Mode Tc), perfectly suited for tunable white luminaires
LDALI-PWM4-RGBW: 4 PWM channels, controlled via a common DALI address (DT8 – Mode RGBWAF)
Maximum current of 3 A per channel
Dimming range from 0.1% to 100%
Adjustable PWM frequency: 125 / 250 (default) / 500 Hz
Externally powered, supply voltage 12 to 24 V DC according to the operating voltage of the LED modules
High efficiency and low standby power consumption
Overtemperature, Open- and Short-circuit protection
DALI-2 certified, supporting IEC 62386-101, IEC62386-102, IEC 62386-207 and IEC 62386-209
Firmware update via DALI

LDALI-PWM4 PWM Modules Products

LDALI-PWM4

PWM module, DALI, 4 x 3 A LED outputs, 24 V DC ext.

LDALI-PWM4-RGBW

PWM module RGBW, DALI, 4 x 3 A LED outputs, 24 V DC ext.

LDALI-PWM4-TC

PWM module tunable white, DALI, 4 x 3 A LED outputs, 24 V DC ext.

The post LDALI-PWM4 PWM Modules appeared first on Kepler Electronics.

LOY-DALI-SBM1 Sunblind Module

Maen Sirhan — Tue, 02 Apr 2024 15:16:25 +0000

The LOY-DALI-SBM1 is a DALI module for controlling sunblinds. The device is bus powered and comes with 2 built-in relay contacts, which are suitable to switch currents of up to 6A at 250 V AC or 30 V DC.

The device provides 2 operating modes:

The Sunblind-Mode (manufacturer specific operating mode 0x80) is well suited for sunblind control due to an extended command set that includes direction and duration information for the blinds connected to the relay outputs. On LOYTEC controllers the device is automatically configured to be used in this mode.

The LOY-DALI-SBM1 is suited to control a single sunblind-motor.

In Relay-Mode (operating mode 0x00) the module acts as DALI‑2 certified relay module with 2 interlocked contacts: normally open and normally closed.

LOY-DALI-SBM1 Sunblind Module Products

LOY-DALI-SBM1

LOY-DALI-SBM1 Sunblind Module

The post LOY-DALI-SBM1 Sunblind Module appeared first on Kepler Electronics.

L-DALI: CEA-709/DALI Controllers

Maen Sirhan — Tue, 02 Apr 2024 15:13:46 +0000

LDALI-3E101-U CEA‑709/DALI Controller

LDALI-3E102-U CEA‑709/DALI Controller

LDALI-3E104-U CEA‑709/DALI Controller

L‑DALI Controllers are multifunctional devices combining constant light control, sunblind control, and gateway functions between LonMark and DALI (Digital Addressable Lighting Interface) systems. With Alarming, Scheduling, Trending, and e-mail notification (AST) the L‑DALI Controller is a perfect solution for DALI lighting systems and for a smooth DALI integration into LonMark Systems.

DALI Network Interface

L-DALI Controllers act as a DALI-Master in the DALI network and can interact with DALI-2 multi-sensors and buttons in Multi-Master mode.The L-DALI lineup for LonMark Systems features 1, 2, or 4 independent DALI channels. Up to 64 DALI or DALI-2 based luminaries per DALI channel can be controlled individually or via 16 groups. All luminaries are monitored for lamp or ballast defect. In addition up to 64 DALI-2 input devices are supported per DALI channel. Each input device can be equipped with push buttons, sliders, occupancy and light sensors.

Built-In DALI Bus Power Supply

All L-DALI models come with a built-in DALI bus power supply. The LDALI-3E101-U and the LDALI-3E102-U can supply each DALI channel with a guaranteed supply current of 230 mA, the LDALI-3E104-U can supply 116 mA per channel. In case of the LDALI-3E104-U an external DALI bus power supply can be added to top up the supply current to 232 mA. External power supplies are available for up to four DALI channels. The internal DALI bus power can be switched on and off via web interface or LCD UI. Thanks to the switching power supply, these devices can handle input voltages from 85 – 240 V AC, 50/60 Hz.

LonMark TP/FT‑10 or Ethernet/IP‑852 Connection

The L‑DALI Controllers provide connectivity in LonMark Systems through IP‑852, or TP/FT‑10 as well as data exchange through Global Connections. They support comprehensive AST functionality (Alarming, Scheduling, and Trending) with e‑mail notification. Full L‑WEB integration is supported as well. The L‑DALI Controllers are equipped with two Ethernet ports including a built-in Ethernet switch.

IoT Integration

The IoT function (Node.js) allows connecting the system to almost any cloud service, either for uploading historical data to analytics services, delivering alarm messages to alarm processing services or operating parts of the control system over a cloud service (e.g., scheduling based on Web calendars or booking systems). Processing Internet information such as weather data in forecast-based control is also possible. Finally, the JavaScript kernel also allows implementing serial protocols to non-standard equipment.

Local Operation and Override

The L‑DALI Controllers come with a built-in backlit display (128×64) and a jog dial for local operation and override. Using the local operation, maintenance tasks (DALI device replacement, burn-in mode, etc.) can be executed without the need of any software tool.

Constant Light Control

The integrated Constant Light Controller (LonMark Functional Profile #3050) allows controlling local DALI ballasts and luminaires via the CEA‑709 network. It supports various lighting control strategies, presence and lux level based. Several parameters can be used to configure the Constant Light Controller for almost any use case.

Sunblind Control with Constant Light Control Interaction

The integrated Sunblind Controller (LonMark Functional Profile #6111) allows intelligent controlling of blinds connected via SMI (requires LSMI-804) or the CEA‑709 network. It offers effective sun and anti-glare protection through active slat control and slat adjustment according to the sun position. Energy efficiency is ensured by linking room occupancy with sun protection. If a room is unoccupied, the L‑DALI Controller opens or closes the sunblinds depending on the thermal requirements. This allows for instance to use the heat of the sun for heating in winter while in summer, the heat from the sun is reduced by the closed blinds to reduce the cooling load.

Optionally, the sunblind and light control applications of a room or an area can be linked together. As both applications control the light available in the room this holistic approach assures maximum comfort and energy efficiency.

In addition to the constant light and sunblind control, any mathematical calculation and function or logical operation (Boolean algebra) can be created on the device and process all available data points.

Device Configuration via Tool or Web Interface

The device configuration, commissioning, and parameterization is done either with the configuration tool software (used as stand-alone tool or as LNS® plug-in) or via the integrated web server.

EnOcean, OPC and Modbus

Wireless EnOcean sensors and buttons can be integrated via the optional L‑ENO EnOcean interface. To use the L‑DALI with an existing SCADA solution all runtime values and parameters can be accessed via OPC (XML/DA and UA) and Modbus TCP.

Advanced DALI Functions

DALI Sensors
The L‑DALI Controllers support the integration of DALI-2 multi-sensors for presence detection and light level recognition. In addition to the LOYTEC DALI-2 multi-sensor LDALI‑MS2/MS2-BT/MS4-BT, DALI-2 sensors of many wellknown manufacturers can be used.
DALI Buttons
For manual operation, DALI-2 push button couplers, like the LDALI-BM2, DALI-2 operation panels, and IR remote controls can be integrated into the system. Their functionality can be configured individually. In addition to controlling lighting via DALI (dimming, scene recall, etc.) and sunblinds via SMI (up, down, etc.), button press events can be propagated in the building network, triggering other, non-lighting related building automation functions. Support of feedback feature for pushbutton instances according to IEC 62386-332 is provided.
DALI Relay Modules
Standard loads in the power grid can be controlled via DALI using DALI relay modules, like the LDALI-RM3, LDALI-RM4 and LDALI-RM8.
DALI Color Control
The L-DALI allows controlling DALI luminaires with colour control functionality (DT8). Both, tunable white (Tc) and full RGB color control (RGBWAF and xycoordinate) are supported. Light color can either be changed automatically, via manual operation (e.g. buttons) or via the network.
Auto Burn-In for Fluorescent Lamps
Fluorescent lamps must be operated about 100 hours with 100 % brightness before they may be dimmed. This burn-in process is monitored by L‑DALI for each lamp. After 100 hours burn-in time, the lamp’s constant light control is enabled.
Automatic Test of Emergency Lighting Systems
In DALI emergency lighting systems based on IEC 62386-202, L-DALI can be used for testing the system. The results can be logged.
Collection of important Operational Parameters
For maximum transparency in the lighting system, L‑DALI can record the operating hours of each lamp and also the energy consumption (calculated).
DALI Device Replacement made easy
Defective DALI ballasts can easily be replaced directly on the L‑DALI Controller (LCD and jog dial) or via the web interface. No software tool is necessary.

LonMark Interface

The L-DALI Controller maps information from the DALI network to Network Variables (NVs) to control DALI ballasts or display operating states including DALI sensor occupancy and lux level information. L-DALI Controller for LonMark Systems can be connected either to an Ethernet/IP channel (LonMark IP-852) or a TP/FT 10 channel. The provided static NV interface includes the following profiles:

Lamp Actuator #3040
Light Sensor #1010
Occupancy Sensor #1060
Constant Light Controller #3050
Sunblind Controller #6111
Open Loop Sensor (button) #1

All data points are available in a tree structure on the integrated web server to be displayed or set using a web browser.

Features

DALI integration into LonMark Systems
Supports up to 64 DALI ballasts and 16 DALI groups per DALI channel
Supports up to 64 input devices overall per channel
Up to 16 DALI sensors per DALI channel are supported
Up to 64 DALI button modules per DALI channel are supported
Integrated DALI bus power supply
Manual operation using the jog dial and local access to information about device status and data points in clear text and symbols
128×64 graphic display with backlight
Built-in web server for device configuration
Test and assignment of DALI devices via the web interface
Replacement of DALI devices without additional software tools via LCD and jog dial
Supports the control of standard loads in the power grid via LDALI-RM3 Relay Modules
Integrated Constant Light Controller
Integrated Sunblind Controller
Supports DALI-2 devices (drivers and input devices)
DALI‑2 certified (compliant with IEC 62386‑101 and IEC 62386‑103)
Support DALI color control (DT8 tunable white & full color control)
Supports lamp burn-in mode
Supports periodic testing of DALI emergency lights
Integrated DALI Protocol Analyzer
Compliant with CEA‑709, CEA‑852 and ISO/IEC 14908-1 standard (LonMark System)
Network connection either with TP/FT‑10 or IP‑852 (CEA‑852 Ethernet)
Alarming, Scheduling, and Trending (AST) locally or embedded in L‑WEB (building management)
Node.js support for easy IoT integration (e.g. Google calendar, Alexa & friends, multimedia equipment,…)
Event-driven e-mail notification
Supports Local and Global Connections
Stores customized graphical pages
Visualization of customized graphical pages through LWEB‑900 (building Management), LWEB‑803 (Monitoring and Control), or LWEB‑802 (Web Browser)
Stores user-defined project documentation
Dual Ethernet/IP interface
Built-in OPC XML‑DA and OPC UA server
Modbus TCP (Master or Slave)
Supports SMI (Standard Motor Interface) through LSMI-804
Connection to EnOcean wireless devices via LENO‑80x Interface Supports WLAN through LWLAN‑800 Interface
Supports LTE through LTE‑800 Interface
Configurable Bluetooth beacons and services: indoor navigation, asset tracking (requires LIC-ASSET license) and access to LWEB-900 room control solution

Tutorials

L-DALI 7.4 Release Tutorial – Features of the new DALI Release

This video provides a detailed overview on the new features of the latest firmware release.

Features of L-INX 8.0 Release

This video presents several features of the new firmware release.

L-DALI: CEA-709/DALI Controllers Products

LDALI-3E101-U

CEA‑709/DALI Controller for IP-852 (Ethernet), 1 DALI channel, integrated DALI power supply

LDALI-3E102-U

CEA‑709/DALI Controller for IP-852 (Ethernet), 2 DALI channels, integrated DALI power supply

LDALI-3E104-U

CEA‑709/DALI Controller for IP-852 (Ethernet), 4 DALI channels, integrated DALI power supply

LIC-ASSET

LIC-ASSET, Add-on Software License to activate asset tracking (for LDALI-ME20x-U, LDALI-3E10x-U, LDALI-PLCx, LROC-400, LROC-401, LIOB-AIR20, LIOB-591)

Contact Sales for quote request

LDALI-PWR1-U

DALI Power Supply for 1 DALI channel, 50mA

LDALI-PWR2-U

DALI-2 power supply, 85-240 V, 50/60 Hz, Output: 2 x 16 VDC, 116 mA (DALI bus)

LDALI-PWR4-U

DALI-2 power supply, 85-240 V, 50/60 Hz, Output: 4 x 16 VDC, 116 mA (DALI bus)

LDALI-MS2-BT

DALI-2 multi-sensor (presence detection, illuminance sensor, IR receiver, temperature sensor, humidity sensor, 3 digital inputs, Bluetooth), up to 12 m mounting height

LDALI-MS4–BT

DALI-2 multi-sensor (presence detection, illuminance sensor, IR receiver, temperature sensor, humidity sensor, 3 digital inputs, Bluetooth, flat lens), up to 5 m mounting height

L-RC1

Infrared remote control for room automation applications

LDALI-PD1

DALI Phase-Cut Dimmer Module

LDALI-BM2

Quadruple DALI pushbutton coupler

LDALI-RM5

DALI Relay Module 10 A, Analog Interface 1 – 10 V

LDALI-RM6

DALI Relay Module 10 A, Analog Interface 1 – 10 V, “spud-mount”

LDALI-RM8

DALI Relay Modul, 8 channel

LSMI-804

Standard Motor Interface for 64 motors, 4 SMI channels via USB

LWLAN-800

Wireless LAN Interface IEEE 802.11bgn

LENO-800

EnOcean Interface 868 MHz Europe

LENO-801

EnOcean Interface 902 MHz USA/Canada

LENO-802

EnOcean Interface 928 MHz Japan

LTE-800

LTE Interface

LDALI-PWM4

PWM module, DALI, 4 x 3 A LED outputs, 24 V DC ext.

LDALI-PWM4-RGBW

PWM module RGBW, DALI, 4 x 3 A LED outputs, 24 V DC ext.

LDALI-PWM4-TC

PWM module tunable white, DALI, 4 x 3 A LED outputs, 24 V DC ext.

The post L-DALI: CEA-709/DALI Controllers appeared first on Kepler Electronics.

L-DALI: BACnet/DALI Controllers

Maen Sirhan — Tue, 02 Apr 2024 15:12:21 +0000

L-DALI:-ME201-U BACnet/DALI Controllers

LDALI-ME202-U BACnet/DALI Controller

LDALI-ME204-U BACnet/DALI Controller

L‑DALI Controllers are multifunctional devices combining constant light control, sunblind control and gateway functions between DALI (Digital Addressable Lighting Interface) and BACnet or Modbus systems. With Alarming, Scheduling, Trending and e-mail notification (AST) the L‑DALI Controller is a perfect solution for DALI lighting systems and for a smooth DALI integration into BACnet or Modbus networks.

DALI Network Interface

L-DALI Controllers act as a DALI-Master in the DALI network which can interact with DALI-2 multi-sensors and buttons in Multi-Master mode. The L-DALI Controllers feature 1, 2, or 4 independent DALI channels. Up to 64 DALI or DALI-2 based luminaries per DALI channel can be controlled individually or via 16 groups. All luminaries are monitored for lamp or ballast defect. In addition up to 64 DALI-2 input devices are supported per DALI channel. Each input device can be equipped with push buttons, sliders, occupancy and light sensors.

Built-In DALI Power Supply

All L-DALI models come with a built-in DALI bus power supply. The LDALI-ME201-U/LDALI-ME202-U can supply its DALI channel with a guaranteed supply current of 230 mA, the LDALI-ME204-U can supply 116 mA per channel. In case of the LDALI-ME204-U an external DALI bus power supply can be added to top up the supply current to 232 mA. External power supplies are available for up to four DALI channels. The internal DALI bus power can be switched on and off via web interface or LCD UI. Thanks to the switching power supply, these devices can handle input voltages from 85 – 240 V AC, 50/60 Hz.

BACnet Connectivity

The L‑DALI Controllers feature connectivity in BACnet networks via BACnet/IP, BACnet/SC or BACnet MS/TP. They also provide data exchange through Global Connections and support comprehensive AST functionality (Alarming, Scheduling, and Trending). Full L‑WEB integration is supported as well. The L‑DALI Controllers are equipped with two Ethernet ports including a built-in Ethernet switch.

IoT Integration

Local Operation and Override

Constant Light Control

The integrated Constant Light Controller works with DALI and with BACnet devices. It supports various lighting control strategies, presence and lux level based. Several parameters can be used to configure the Constant Light Controller for almost any use case.

Sunblind Control with Constant Light Control Interaction

The integrated Sunblind Controller application allows intelligent controlling of blinds connected via SMI (requires LSMI-804). It offers effective sun and anti-glare protection through active slat control and slat adjustment according to the sun position. Energy efficiency is ensured by linking room occupancy with sun protection. If a room is unoccupied, the L‑DALI Controller opens or closes the sunblinds depending on the thermal requirements. This allows for instance to use the heat of the sun for heating in winter while in summer, the heat from the sun is reduced by the closed blinds to reduce the cooling load.

Device Configuration via Tool or Web Interface

The device configuration, commissioning, and parameterization is done either with the configuration tool software or via the integrated web server.

EnOcean, OPC and Modbus

EnOcean sensors and buttons can be integrated via the optional L‑ENO EnOcean interface. To use the L‑DALI with an existing SCADA solution all run-time values and parameters can be accessed via BACnet, OPC (XML/DA and UA) and Modbus TCP. 5, 10 or 15 devices can be connected via Modbus RTU (RS-485), the actual number of supported devices is dependent on the activated licenses (LIC-MOD5, LIC-MOD10 or both).

Advanced DALI Functions

DALI Sensors
The L-DALI Controllers support the integration of DALI-2 multi-sensors for presence detection and light level recognition. In addition to the LOYTEC multi-sensors LDALI-MS2-BT/MS3-BT/MS4-BT, DALI-2 sensors of many well-known manufacturers can be used. For asset tracking in office buildings with the LOYTEC multi-sensors (LDALI-MSx-BT), a LIC-ASSET license is required.
DALI Buttons
For manual operation, DALI-2 push button couplers, like the LDALI-BM2, DALI-2 operation panels and IR remote controls can be integrated into the system. Their functionality can be configured individually. In addition to controlling lighting via DALI (dimming, scene recall, etc.) and sunblinds via SMI (up, down, etc.), button press events can be propagated in the building network, triggering other, non-lighting related building automation functions.
DALI Relay Modules
Standard loads in the power grid can be controlled via DALI using DALI relay modules, like the LDALI-RM5 / LDALI-RM6 /LDALI-RM8.
DALI Color Control
The L-DALI allows controlling DALI luminaires with color control functionality (DT8). Both, tunable white (Tc) and full RGB color control (RGBWAF and xycoordinate) are supported. Light color can either be changed automatically, via manual operation (e.g. buttons) or via the network.
Auto Burn-In for Fluorescent Lamps
Fluorescent lamps must be operated about 100 hours with 100 % brightness before they may be dimmed. This burn-in process is monitored by L‑DALI for each lamp. After 100 hours burn-in time, the lamp’s constant light control is enabled.
Automatic Test of Emergency Lighting Systems
IIn DALI emergency lighting systems based on IEC 62386-202, L-DALI can be used for testing the sys-tem. The results can be logged.
Collection of Important Operational Parameters
For maximum transparency in the lighting system, L‑DALI can record the operating hours of each lamp and also the energy consumption (calculated).
DALI Device Replacement made Easy
Defective DALI ballasts can easily be replaced directly on the L‑DALI Controller (LCD and jog dial) or via the web interface. No software tool is necessary.

Smooth DALI integration into BACnet and Modbus Networks

The L‑DALI Controller maps information from the DALI network to BACnet objects or Modbus registers that are used to control DALI ballasts or to display operating states.

BACnet Interface

The following BACnet server objects are supported:

Analog Output objects to control DALI ballasts, groups, and channels
Multi-State Output objects for scene control of DALI groups and channels Analog Input objects providing feedback from DALI ballast, groups, and channels
Analog Input objects providing status information from DALI groups and channels
Accumulator objects providing estimated energy usage of DALI groups and channels
Multi-State Output objects to issue commands (start/stop emergency test or burn-in, change color temperature, etc.) to DALI ballasts, groups and channels
Analog Input objects providing battery status of emergency ballasts, groups
Analog Input objects providing lux level information from supported DALI sensors
(LDALI-MS2: additionally humidity and temperature information is provided)
Binary Input objects providing occupancy information from supported DALI sensors
Loop objects providing constant light controller functionality
Binary Input objects providing button information from supported DALI buttons
Various objects to control sunblinds

All data points are available on the web server in a tree structure and can be displayed and set via a web browser.

Features

DALI integration into BACnet networks
Supports up to 64 DALI ballasts and 16 DALI groups per DALI channel
Supports up to 64 input devices overall per channel
Up to 16 DALI sensors per DALI channel are supported
Up to 64 DALI button modules per DALI channel are supported
Integrated DALI bus power supply
Manual operation using the jog dial and local access to information about device status and data points in clear text and symbols
128×64 graphic display with backlight
Built-in web server for device configuration
Test and assignment of DALI devices on the web interface
Replacement of DALI devices without additional software tools via LCD and jog dial
Supports the control of standard loads in the power grid via LDALI-RM3 Relay Modules
Integrated Constant Light Controller
Integrated Sunblind Controller
Supports DALI-2 devices (drivers and input devices)
DALI-2 certified (compliant with IEC 62386-101 and IEC 62386-103)
Support DALI color control (DT8 tunable white & full color control)
Supports lamp burn-in mode
Supports periodic testing of DALI emergency lights
Integrated DALI Protocol Analyzer
Compliant with ANSI/ASHRAE 135‑2012 and ISO 16484‑5:2012 standard
Supports BACnet MS/TP, BACnet/IP or BACnet/SC
BACnet Client Function (Write Property, Read Property, COV Subscription)
B-BC (BACnet Building Controller) functionality, BTL certified
Alarming, Scheduling, and Trending (AST) locally or embedded in L‑WEB (building management)
Node.js support for easy IoT integration (e.g. Google calendar, Alexa & friends, multimedia equipment,…)
Event-driven e-mail notification
Supports Local and Global Connections
Stores customized graphical pages
Visualization of customized graphical pages through LWEB‑900 (building Management), LWEB‑803 (Monitoring and Control), or LWEB‑802 (Web Browser)
Stores user-defined project documentation
Dual Ethernet/IP interface
Built-in OPC XML‑DA and OPC UA server
Modbus TCP or Modbus RTU/ASCII (Master or Slave)
Supports SMI (Standard Motor Interface) through LSMI-804
Connection to EnOcean wireless devices via LENO‑80x Interface
Supports WLAN through LWLAN‑800 Interface
Supports LTE through LTE‑800 Interface
Modbus RTU/ASCII for 5 devices (LIC-MOD5 required), 10 devices (LIC-MOD10 required) or 15 devices (LIC-MOD5 and LIC-MOD10 required)
Configurable Bluetooth beacons and services: indoor navigation, asset tracking (requires LIC-ASSET license) and access to LWEB-900 room control solution

Tutorials

L-DALI 7.4 Release Tutorial – Features of the new DALI Release

This video provides a detailed overview on the new features of the latest firmware release.

Features of L-INX 8.0 Release

This video presents some features of the newfirmware release.

L-DALI: BACnet/DALI Controllers Products

LDALI-ME201-U

BACnet/DALI Controller, 1 DALI channel, integrated DALI power supply

LDALI-ME202-U

BACnet/DALI Controller, 2 DALI channel, integrated DALI power supply

LDALI-ME204-U

BACnet/DALI Controller, 4 DALI channels, integrated DALI power supply

LIC-ASSET

LIC-ASSET, Add-on Software License to activate asset tracking (for LDALI-ME20x-U, LDALI-3E10x-U, LDALI-PLCx, LROC-400, LROC-401, LIOB-AIR20, LIOB-591)

Contact Sales for quote request

LIC-MOD5

License to add 5 Modbus devices for LDALI-ME201-U, LDALI-ME202-U, LDALI-ME204-U

LIC-MOD10

License to add 10 Modbus devices for LDALI-ME201-U, LDALI-ME202-U, LDALI-ME204-U

LDALI-PWR1-U

DALI Power Supply for 1 DALI channel, 50mA

LDALI-PWR2-U

DALI-2 power supply, 85-240 V, 50/60 Hz, Output: 2 x 16 VDC, 116 mA (DALI bus)

LDALI-PWR4-U

DALI-2 power supply, 85-240 V, 50/60 Hz, Output: 4 x 16 VDC, 116 mA (DALI bus)

LDALI-MS2-BT

DALI-2 multi-sensor (presence detection, illuminance sensor, IR receiver, temperature sensor, humidity sensor, 3 digital inputs, Bluetooth), up to 12 m mounting height

LDALI-MS4-BT

DALI-2 multi-sensor (presence detection, illuminance sensor, IR receiver, temperature sensor, humidity sensor, 3 digital inputs, Bluetooth, flat lens), up to 5 m mounting height

LDALI-PD1

DALI Phase-Cut Dimmer Module

L-RC1

Infrared remote control for room automation applications

LDALI-BM2

Quadruple DALI pushbutton coupler

LDALI-RM5

DALI Relay Module 10 A, Analog Interface 1 – 10 V

LDALI-RM6

DALI Relay Module 10 A, Analog Interface 1 – 10 V, “spud-mount”

LDALI-RM8

DALI Relay Modul, 8 channel

LSMI-804

Standard Motor Interface for 64 motors, 4 SMI channels via USB

LWLAN-800

EnOcean Interface 868 MHz Europe

LENO-801

EnOcean Interface 902 MHz USA/Canada

LENO-802

EnOcean Interface 928 MHz Japan

LTE-800

LTE Interface

LRS232-802

USB to 2x RS-232 Interface

LDALI-PWM4

PWM module, DALI, 4 x 3 A LED outputs, 24 V DC ext

LDALI-PWM4-RGBW

PWM module RGBW, DALI, 4 x 3 A LED outputs, 24 V DC ext.

LDALI-PWM4-TC

PWM module tunable white, DALI, 4 x 3 A LED outputs, 24 V DC ext.

The post L-DALI: BACnet/DALI Controllers appeared first on Kepler Electronics.

LDALI‑PLC2 LDALI‑PLC4: Programmable DALI Controller

Maen Sirhan — Fri, 29 Mar 2024 09:15:08 +0000

Product available through Competence Partner Program
L-FOCUS: L-DALI Lighting Control Solutions (English)
LDALI-PLC2/PLC4 Datasheet
L-DALI User Manual
LDALI-PLC2/PLC4 Installation Instructions
L-DALI Compatibility List
Certificates: EC / BTL / DALI-2 / AMEV
Downloads: LDALI-PLC2 / LDALI-PLC4

The LDALI‑PLC2/PLC4 controllers are powerful, programmable lighting controllers, which can be programmed by L‑STUDIO. With Alarming, Scheduling, Trending and e‑mail notification (AST) the LDALI‑PLC2/PLC4 controller is a perfect solution for DALI lighting systems with application requirements not covered by the standard application of the non‑programmable L‑DALI controllers.

DALI Network Interface

L‑DALI Controllers act as a DALI‑Master in the DALI network and can interact withDALI‑2 multi‑sensors and buttons in Multi‑Master mode. The LDALI‑PLC2/PLC4 is equipped with 2/4 independent DALI channels. Up to 64 DALI or DALI‑2 basedluminaries per DALI channel can be controlled individually or via 16 groups. Allluminaries are monitored for lamp or ballast defect. In addition up to 64 DALI‑2input devices are supported per DALI channel. Each input device can be equipped with push buttons, sliders, occupancy and light sensors.

Built-In DALI Bus Power Supply

The LDALI‑PLC4 comes with a built‑in DALI bus power supply, which can supply each DALI channel with a guaranteed supply current of 116 mA. An external DALI bus power supply can be added to top up the supply current to 232 mA. External power supplies are available for up to four DALI channels. The LDALI‑PLC2 pro‑vides a DALI‑bus power supply with guaranteed supply current of 230mA per channel. The internal DALI bus power can be switched on and off via web interface or LCD UI. Thanks to the switching power supply, these devices can handle input voltages from 85 – 240 V AC, 50/60 Hz.

Local Operation and Override

The L‑DALI Controllers come with a built‑in backlit display (128×64) and a jog dial for local operation and override. Using the local operation, maintenance tasks (DALI device replacement, burn‑in mode, etc.) can be executed without the need of any software tool.

Programmable

The LDALI‑PLC2/PLC4 can be programmed using the L‑STUDIO programming tool. It can be programmed using IEC 61499 for integration into the L‑ROC system and IEC 61131 for stand-alone operation.

IEC 61131 lighting control library available

A library containing standard lighting control functionality is available. It supports various lighting control strategies, presence and lux level based. Several parame‑ters can be used to configure the application for almost any use case. User specific program extensions are possible as well.

Connectivity

The LDALI‑PLC2/PLC4 controller provides connectivity functions to concurrently integrate CEA‑709 (LonMark Systems), BACnet, KNX, and Modbus subsystems. LonMark Systems can be integrated via IP‑852 (Ethernet/IP). BACnet integration is supported through BACnet/IP (Ethernet/IP), BACnet/SC or BACnet MS/TP (RS‑485), KNXnet/IP and Modbus TCP via Ethernet/IP.

The gateway functionality allows data communication between all communication technologies available on the device. Different technology data points are mapped through Local Connections on the device. The mapping of different technology data points on distributed devices is supported by Global Connections.

Each L-DALI Controller is equipped with two Ethernet ports. It can either be configured to use the internal switch to interconnect the two ports or every port is configured to work in a separate IP network.

When the Ethernet ports are configured for two separate IP networks, one port can be connected for instance to a WAN (Wide Area Network) with enabled network security (HTTPS) while the second port can be configured to be connected to an insecure network (LAN) where the standard building automation protocols like BACnet/IP, LON/IP, or Modbus TCP are present. These devices also feature firewall functionality to isolate particular protocols or services between the ports.

Using the internal switch, a daisy chained line topology of up to 20 devices can be built, which reduces costs for network installation. The IP switch also allows the setup of a redundant Ethernet installation (ring topology), which increases reliability. The redundant Ethernet topology is enabled by the Rapid Spanning Tree Protocol (RSTP), which is supported by most managed switches.

The L-DALI Controllers provide fully featured AST functionality (Alarming, Scheduling, and Trending) and can be integrated perfectly into the L‑WEB System.

IoT Integration

Device Configuration via Tool or Web Interface

The device configuration, commissioning, and parameterization is done either with the configuration tool software or via the integrated web server.

EnOcean, SMI and LIOB/‌IP

Wireless EnOcean sensors and buttons can be integrated via the optional L‑ENO EnOcean interface. For sunblinds the LSMI-804 extension module allows the integration of up to four SMI channels. Physical I/Os can be integrated through L‑IOB I/O Modules via LIOB‑IP.

Advanced DALI Functions

DALI Sensors
The L-DALI Controllers support the integration of DALI-2 multi-sensors for presence detection and light level recognition. In addition to the LOYTEC multi-sensors LDALI‑MS2-BT/MS3‑BT/MS4‑BT, DALI-2 sensors of many well-known manufacturers can be used.
DALI Buttons
For manual operation, DALI-2 push button couplers, like the LDALI-BM2, DALI-2 operation panels, and IR remote controls can be integrated into the system. The function executed when a button is pressed is freely programmable in the program logic. In addition the feedback feature for pushbutton instances according to IEC 62386‑332 is supported.
DALI Relay Modules
Standard loads in the power grid can be controlled via DALI using DALI relay modules, like the LDALI-RM5, LDALI-RM6 and LDALI-RM8.
DALI Color Control
The LDALI allow controlling DALI luminaires with color control functionality (DT8). Both, tunable white (Tc) and full RGB color control (RGBWAF and xy-coordinate) are supported. Changing the light colour is possible via scenes or controlled via the program logic.
Auto Burn-In for fluorescent Lamps
Fluorescent lamps must be operated about 100 hours with 100 % brightness before they may be dimmed. This burn-in process is monitored by L‑DALI for each lamp. After 100 hours burn-in time, the lamp’s constant light control is enabled.
Automatic Test of Emergency Lighting Systems
In DALI emergency lighting systems based on IEC 62386-202, L-DALI can be used for testing the system. The results can be logged.
Collection of important operational Parameters
For maximum transparency in the lighting system, L‑DALI can record the operating hours of each lamp and also the energy consumption (calculated).
DALI Device Replacement made easy
Defective DALI ballasts can easily be replaced directly on the L‑DALI Controller (LCD and jog dial) or via the web interface. No software tool is necessary.

Features

Programmable with L‑STUDIO IEC 61131‑3 and IEC 61499
Supports up to 64 DALI ballasts and 16 DALI groups per DALI channel
Supports up to 64 input devices overall per channel
Up to 16 DALI sensors per DALI channel are supported
Up to 64 DALI button modules per DALI channel are supported
Integrated DALI bus power supply
DALI‑2 certified
Manual operation using the jog dial and local access to information about device status and data points in clear text and symbols
128×64 graphic display with backlight
Built‑in web server for device configuration
Test and assignment of DALI devices on the web interface
Replacement of DALI devices without additional software tools via LCD and jog dial
Supports the control of standard loads in the power grid via LDALI‑RM5/RM6/RM8 Relay Modules
Supports DALI‑2 devices (drivers and input devices)
Support DALI color control (DT8 tunable white & full color control)
Supports lamp burn‑in mode
Supports periodic testing of DALI emergency lights
Integrated DALI Protocol Analyzer
Physical inputs and outputs with L‑IOB I/O Modules
Compliant with CEA‑709, CEA‑852, and ISO/IEC 14908 Standard (LonMark System)
Support of dynamically created or static NVs
Support of user‑defined NVs (UNVTs) and Configuration Properties (SCPTs, UCPTs)
KNXnet/IP
Gateway functions including Smart Auto‑Connect
Modbus TCP and Modbus RTU/ASCII
Compliant with ANSI/ASHRAE135‑2012 and ISO16484‑5:2012 standard
Supports BACnet MS/TP, BACnet/IP or BACnet/SC
BACnet Client Function (Write Property, Read Property, COV Subscription)
B‑BC (BACnet Building Controller) functionality, BTL certified
Alarming, Scheduling, and Trending (AST) locally or embedded in L‑WEB (building management)
Node.js support for easy IoT integration (e.g. Google calendar, Alexa & friends, multimedia equipment,…)
Event‑driven e‑mail notification
Supports Local and Global Connections
Built‑in OPCXML‑DA and OPCUA server
Stores customized graphical pages
Visualization of customized graphical pages through LWEB‑900 (building Management), LWEB‑803 (Monitoring and Control), or LWEB‑802 (Web Browser)
Stores user‑defined project documentation
Dual Ethernet/IP interface
Supports SMI (Standard Motor Interface) through LSMI‑804
Connection to EnOcean wireless devices via LENO‑80x Interface
Supports WLAN through LWLAN‑800 Interface
Supports LTE through LTE‑800 Interface
Configurable Bluetooth beacons and services: indoor navigation, asset tracking (requires LIC-ASSET license) and access to LWEB-900 room control solution

Tutorials

Light Library Tutorial

The video shows basic steps on how to create a light application with the LDALI-PLC2/PLC4 in L-STUDIO.

L-DALI 7.4 Release Tutorial – Features of the new DALI Release

This video provides a detailed overview on the new features of the latest firmware release.

Features of L-INX 8.0 Release

This video presents some features of the new firmware release.

LDALI‑PLC2 / LDALI‑PLC4: Programmable DALI Controller Products

LDALI-PLC2

Programmable DALI Controller, 2 DALI channels, integrated DALI power supply

LDALI-PLC4

Programmable DALI Controller, 4 DALI channels, integrated DALI power supply

L-STUDIO

Device configuration and programming suite

LIC-ASSET

LIC-ASSET, Add-on Software License to activate asset tracking (for LDALI-ME20x-U, LDALI-3E10x-U, LDALI-PLCx, LROC-400, LROC-401, LIOB-AIR20, LIOB-591)

Contact Sales for quote request

LOY-DALI-SBM1

LOY-DALI-SBM1 Sunblind Module

LDALI-PWR1-U

DALI Power Supply for 1 DALI channel, 50mA

LDALI-PWR2-U

DALI-2 power supply, 85-240 V, 50/60 Hz, Output: 2 x 16 VDC, 116 mA (DALI bus)

LDALI-PWR4-U

DALI-2 power supply, 85-240 V, 50/60 Hz, Output: 4 x 16 VDC, 116 mA (DALI bus)

LDALI-MS2-BT

DALI-2 multi-sensor (presence detection, illuminance sensor, IR receiver, temperature sensor, humidity sensor, 3 digital inputs, Bluetooth), up to 12 m mounting height

LDALI-MS4-BT

DALI-2 multi-sensor (presence detection, illuminance sensor, IR receiver, temperature sensor, humidity sensor, 3 digital inputs, Bluetooth, flat lens), up to 5 m mounting height

LDALI-BM2

Quadruple DALI pushbutton coupler

LDALI-RM5

DALI Relay Module 10 A, Analog Interface 1 – 10 V

LDALI-RM6

DALI Relay Module 10 A, Analog Interface 1 – 10 V, “spud-mount”

LDALI-RM8

DALI Relay Modul, 8 channel

LDALI-PD1

DALI Phase-Cut Dimmer Module

LWLAN-800

Wireless LAN Interface IEEE 802.11bgn

LENO-800

EnOcean Interface 868 MHz Europe

LENO-801

LENO-802

EnOcean Interface 928 MHz Japan

LRS232-802

USB to 2x RS-232 Interface

LSTAT-810-G3-L0

Remote EnOcean Antenna, Europe, White

LSTAT-820-G3-L0

Remote EnOcean Antenna, USA/CA, White

LSTAT-830-G3-L0

Remote EnOcean Antenna, Japan, White

LSMI-804

Standard Motor Interface for 64 motors, 4 SMI channels via USB

LTE-800

LTE Interface

L-RC1

Infrared remote control for room automation applications

LDALI-PWM4

PWM module, DALI, 4 x 3 A LED outputs, 24 V DC ext.

LDALI-PWM4-TC

PWM module tunable white, DALI, 4 x 3 A LED outputs, 24 V DC ext.

LDALI-PWM4-RGBW

LSTAT-810-GX-LX-CU

LSTAT-800 based custom design, includes EnOcean interface, minimum quantity 100 pcs, enclosure G1: silver, G2: black, G3: white; custom print Lx, including 2 working samples, lead time 10 weeks (needs LSTAT-80x-CUSTOM)

LSTAT-812-GX-LX-CU

LSTAT-802 based custom design, includes EnOcean interface, minimum quantity 100 pcs, enclosure G1: silver, G2: black, G3: white; custom print Lx, including 2 working samples, lead time 10 weeks (needs LSTAT-80x-CUSTOM)

LSTAT-80x-CUSTOM

One-time customization cost for L-STAT custom design, including 2 working samples

The post LDALI‑PLC2 LDALI‑PLC4: Programmable DALI Controller appeared first on Kepler Electronics.