DALI Controllers Archives - Kepler Electronics

KDALI-RM-10V

Maen Sirhan — Sat, 27 Apr 2024 07:07:20 +0000

Contact Sales for quote request
Download KDALI-RM-10V User Manual

DALI Relay Module + DALI to 0/1-10V Converter KDALI-RM-10V

The KDALI-RM-10V is a DALI relay module plus DALI to 0/1-10V converter which is capable of switching both AC and DC loads and controlling 0/1-10V dimmable loads, The max switching voltage for AC loads is 250V, and the max switching voltage for DC loads is 50V. The DALI RM enables to integrate existing loads which do not have DALI input into DALI circuit and switch on/off the loads. The DALI to 0/1-10V converter enables to integrate 0/1-10V dimmable loads into DALI circuit and control the loads via DALI.
The max. load capacity for conventional incandescent and halogen light sources is 1000W (5) 2 30V, and max. load capacity for LED light sources is 300W @ 230V. It is easy to be installed into existing standard wall boxes or mounted on 35mm DIN rail with an extra mounting bracket.

Key Features

DALI relay module + DALI to 0/1-10V converter
2 in 1 DT6 & DT7 versions available
DALI-2 certified
Enable to switch power of the 0/1-10V load through the relay
DALI bus powered, no extra power supply required
1 DALI address can be assigned by DALI master controller
Control of one standard contactor
Compact relay module for controlling a standard contactor via DALI
Loads that do not have a DALI input, can therefore integrated in the DALI circuit
The loads can be switched on and off via DALI
Compatible with universal DALI systems and master controllers in the market
Mini Size, easy to be Installed into a standard wall box
5 years warranty
Waterproof grade: IP20

Specification

Part No.	Switching Voltage AC	Switching Voltage DC	Relay Output Current	Load type	DALI Consumption	0/1 10V Output	Dimension (mm)
KDALI-RM-10V	Max. 250V	Max. 30V	Resistive load: max.4.3A Capacitive load: max. 1.3A Inductive load: max.4.3A	Incandescent Hv-halogen lamps LED lamps	<3mA	<10mA	45×45.5×20.3

Product Dimension

Wiring Diagram

The post KDALI-RM-10V appeared first on Kepler Electronics.

KDALI-KNX-2CH

Maen Sirhan — Thu, 25 Apr 2024 08:31:10 +0000

KNX to 2 Channel DALI Gateway KDALI-KNX-2CH

The KNX DALI Gateway is a DIN rail module for installation in the distribution board on a 55 mm mounting raiL It is a DALI single-master controller to DALI standard IEC 62386 Parts 101ed2 and lOSedl.The gateway is suitable for use with DALI and DALI-2 systems.lt supports Device Type 6. Device Type 8 Tc, Device Type 8 XY coordinate. Device Type 8 RGB with DALI interfaces to IEC 62386 and their integration in a KNX building installation.The DALI gateway has 2 channels DALI output Up to 64 DALI devices can be connected to each DALI output DT6 and DT8 devices can all be connected to each DALI output in a mixed configuration.The lamps connected to each DALI channels are controlled via KNX usinghroadcast64 individual lamps;16 lighting groups;16 scenes

Key Features

Integrated DALI into KNX system
2 channels DALI output
Each DALI channel with 25CmA DALI PS output
No ext’a DALI PS required. simpLe wiring
Supports all DALI DT6 & DTS device types
Mini USB port to connect to DALI PC software
Programmable through ETS software
DALI bus state monitor indicator

Specification

Product Dimension

Wiring Diagram

The post KDALI-KNX-2CH appeared first on Kepler Electronics.

KDALI-MASTER-1CH

Maen Sirhan — Wed, 24 Apr 2024 20:39:12 +0000

DIN Rail DALI master controller KDALI-MASTER-1CH

The DIN Rail DALI master controller KDALI-MASTER-1CH is a central controller of a DALI system to control DALI control gears and configure DALI-2 input devices on the DALI line. Each DALI channel enables to automatically assign and manage addreses to up to 64 control gears, the control gears can assigned to up to 16 groups.The DALI-2 master supports 5 DALI control gear device types: DT6, DT8, Te, DT8, XY coordinate, DT8 RGBWA, DT7 Switching actuator. Each DALI channel also supports all types of DALI-2 input devices include push buttons, motion sensors, light sensor, rotary switch and touch panels. Each DALI channel can address and manage up to 64 DALI-2 input devices, the input devices can assigned to up to 32 groups. Each DALI channel enables to set up to 16 DALI scenes. It enables to set up to 256 timer tasks. It enables to set up to 4 types brightness fade and color fade cycle schedules. It enables to set up to 4 Bionic color temperature schedules for the CCT control gears to mimic natural light change during 24 hours of a day (Human Centric Lighting). It is designed with PC configuration software tool, enables to configure and read parameters of the DALI control panel and control gears, and manage the control panel and control gears.
This DALI master is designed with built-in 230m A DALI PS to power the DALI circuit.

Meanwhile dip switches can be used to disable or enable built-in DALI PS. Once built-in DALI PS is disabled, the master controller can be connected to an external DALI PS,The DALI master can be easily mounted on 35mm standard DIN rail.

Key Features

Central controller of a DALI system to control DALI control gears on the DALI line
Designed with built-in 230mA DALI PS to power the DALI circuit
Dip switches can used to disable or enable built-in DALI PS
Once built-in DALI PS is disabled, the master controller can be connected to an external DALI PS
Each DALI channel enables to automatically assign and manage addreses to up to 64 control gears
The control gears can assigned to up to 16 groups
Supports 5 DALI control gear device types: DT6, DT8 Te, DT8 XY coordinate, DT8 RGBWA, DT7 Switching actuator
Each DALI channel also supports all types of DALI-2 input devices include push buttons, motion sensors, light sensor, rotary switch and touch panels
Each DALI channel can address and manage up to 64 DALI-2 input devices
The input devices can assigned to up to 32 groups.
Each DALI channel enables to set up to 16 DALI scenes
Enables to set up to 256 timer tasks
Enables to set up to 4 types brightness fade and color fade cycle schedules
Enables to set up to 4 Bionic color temperature schedules for the CCT control gears to mimic natural light change during 24 hours of a day (Human Centric Lighting)
Designed with PC configuration software tool, enables to configure and read parameters of the master and control gears
Can easily mounted on 35 mm standard DIN rail

Wiring Diagram

The post KDALI-MASTER-1CH appeared first on Kepler Electronics.

KDALI-RPT

Maen Sirhan — Wed, 24 Apr 2024 19:53:51 +0000

DALI Repeater with Built-in Bus Power Supply KDALI-RPT

KDALI-RPT is a universal DALI signal repeater with built-in bus power supply, which can prolong DALI signal transmission distance of DALI circuit, with built-in DALI bus power supply, the dali repeater enables to establish a subordinate dali circuit from the main DALI circuit without extra DALI power supply required.

Key Features

DALI repeater with integrated DALI power supply
Device to enhance the maximum DALI cable length from 300m up to 600m
Enhancement and Transmission of the DALI-signals (bidirectional)
Galvanic separation between DALI circuits
Either radially arranged network layout or cascaded system mounting operated with single master
restricted cascading (Series wiring) of multiple repeaters in multi-master operating mode
The maximum amount of DALI-devices in the total network is limited to 64, the devices can be divided on the subordinate circuits at will
For each subordinate DALI circuits no extra DALI power supply required

Product Dimension

Wiring Diagram

The post KDALI-RPT appeared first on Kepler Electronics.

L-DALI: CEA-709/DALI Controllers

Maen Sirhan — Tue, 02 Apr 2024 15:13:46 +0000

LDALI-3E101-U CEA‑709/DALI Controller

LDALI-3E102-U CEA‑709/DALI Controller

LDALI-3E104-U CEA‑709/DALI Controller

L‑DALI Controllers are multifunctional devices combining constant light control, sunblind control, and gateway functions between LonMark and DALI (Digital Addressable Lighting Interface) systems. With Alarming, Scheduling, Trending, and e-mail notification (AST) the L‑DALI Controller is a perfect solution for DALI lighting systems and for a smooth DALI integration into LonMark Systems.

DALI Network Interface

L-DALI Controllers act as a DALI-Master in the DALI network and can interact with DALI-2 multi-sensors and buttons in Multi-Master mode.The L-DALI lineup for LonMark Systems features 1, 2, or 4 independent DALI channels. Up to 64 DALI or DALI-2 based luminaries per DALI channel can be controlled individually or via 16 groups. All luminaries are monitored for lamp or ballast defect. In addition up to 64 DALI-2 input devices are supported per DALI channel. Each input device can be equipped with push buttons, sliders, occupancy and light sensors.

Built-In DALI Bus Power Supply

All L-DALI models come with a built-in DALI bus power supply. The LDALI-3E101-U and the LDALI-3E102-U can supply each DALI channel with a guaranteed supply current of 230 mA, the LDALI-3E104-U can supply 116 mA per channel. In case of the LDALI-3E104-U an external DALI bus power supply can be added to top up the supply current to 232 mA. External power supplies are available for up to four DALI channels. The internal DALI bus power can be switched on and off via web interface or LCD UI. Thanks to the switching power supply, these devices can handle input voltages from 85 – 240 V AC, 50/60 Hz.

LonMark TP/FT‑10 or Ethernet/IP‑852 Connection

The L‑DALI Controllers provide connectivity in LonMark Systems through IP‑852, or TP/FT‑10 as well as data exchange through Global Connections. They support comprehensive AST functionality (Alarming, Scheduling, and Trending) with e‑mail notification. Full L‑WEB integration is supported as well. The L‑DALI Controllers are equipped with two Ethernet ports including a built-in Ethernet switch.

IoT Integration

The IoT function (Node.js) allows connecting the system to almost any cloud service, either for uploading historical data to analytics services, delivering alarm messages to alarm processing services or operating parts of the control system over a cloud service (e.g., scheduling based on Web calendars or booking systems). Processing Internet information such as weather data in forecast-based control is also possible. Finally, the JavaScript kernel also allows implementing serial protocols to non-standard equipment.

Local Operation and Override

The L‑DALI Controllers come with a built-in backlit display (128×64) and a jog dial for local operation and override. Using the local operation, maintenance tasks (DALI device replacement, burn-in mode, etc.) can be executed without the need of any software tool.

Constant Light Control

The integrated Constant Light Controller (LonMark Functional Profile #3050) allows controlling local DALI ballasts and luminaires via the CEA‑709 network. It supports various lighting control strategies, presence and lux level based. Several parameters can be used to configure the Constant Light Controller for almost any use case.

Sunblind Control with Constant Light Control Interaction

The integrated Sunblind Controller (LonMark Functional Profile #6111) allows intelligent controlling of blinds connected via SMI (requires LSMI-804) or the CEA‑709 network. It offers effective sun and anti-glare protection through active slat control and slat adjustment according to the sun position. Energy efficiency is ensured by linking room occupancy with sun protection. If a room is unoccupied, the L‑DALI Controller opens or closes the sunblinds depending on the thermal requirements. This allows for instance to use the heat of the sun for heating in winter while in summer, the heat from the sun is reduced by the closed blinds to reduce the cooling load.

Optionally, the sunblind and light control applications of a room or an area can be linked together. As both applications control the light available in the room this holistic approach assures maximum comfort and energy efficiency.

In addition to the constant light and sunblind control, any mathematical calculation and function or logical operation (Boolean algebra) can be created on the device and process all available data points.

Device Configuration via Tool or Web Interface

The device configuration, commissioning, and parameterization is done either with the configuration tool software (used as stand-alone tool or as LNS® plug-in) or via the integrated web server.

EnOcean, OPC and Modbus

Wireless EnOcean sensors and buttons can be integrated via the optional L‑ENO EnOcean interface. To use the L‑DALI with an existing SCADA solution all runtime values and parameters can be accessed via OPC (XML/DA and UA) and Modbus TCP.

Advanced DALI Functions

DALI Sensors
The L‑DALI Controllers support the integration of DALI-2 multi-sensors for presence detection and light level recognition. In addition to the LOYTEC DALI-2 multi-sensor LDALI‑MS2/MS2-BT/MS4-BT, DALI-2 sensors of many wellknown manufacturers can be used.
DALI Buttons
For manual operation, DALI-2 push button couplers, like the LDALI-BM2, DALI-2 operation panels, and IR remote controls can be integrated into the system. Their functionality can be configured individually. In addition to controlling lighting via DALI (dimming, scene recall, etc.) and sunblinds via SMI (up, down, etc.), button press events can be propagated in the building network, triggering other, non-lighting related building automation functions. Support of feedback feature for pushbutton instances according to IEC 62386-332 is provided.
DALI Relay Modules
Standard loads in the power grid can be controlled via DALI using DALI relay modules, like the LDALI-RM3, LDALI-RM4 and LDALI-RM8.
DALI Color Control
The L-DALI allows controlling DALI luminaires with colour control functionality (DT8). Both, tunable white (Tc) and full RGB color control (RGBWAF and xycoordinate) are supported. Light color can either be changed automatically, via manual operation (e.g. buttons) or via the network.
Auto Burn-In for Fluorescent Lamps
Fluorescent lamps must be operated about 100 hours with 100 % brightness before they may be dimmed. This burn-in process is monitored by L‑DALI for each lamp. After 100 hours burn-in time, the lamp’s constant light control is enabled.
Automatic Test of Emergency Lighting Systems
In DALI emergency lighting systems based on IEC 62386-202, L-DALI can be used for testing the system. The results can be logged.
Collection of important Operational Parameters
For maximum transparency in the lighting system, L‑DALI can record the operating hours of each lamp and also the energy consumption (calculated).
DALI Device Replacement made easy
Defective DALI ballasts can easily be replaced directly on the L‑DALI Controller (LCD and jog dial) or via the web interface. No software tool is necessary.

LonMark Interface

The L-DALI Controller maps information from the DALI network to Network Variables (NVs) to control DALI ballasts or display operating states including DALI sensor occupancy and lux level information. L-DALI Controller for LonMark Systems can be connected either to an Ethernet/IP channel (LonMark IP-852) or a TP/FT 10 channel. The provided static NV interface includes the following profiles:

Lamp Actuator #3040
Light Sensor #1010
Occupancy Sensor #1060
Constant Light Controller #3050
Sunblind Controller #6111
Open Loop Sensor (button) #1

All data points are available in a tree structure on the integrated web server to be displayed or set using a web browser.

Features

DALI integration into LonMark Systems
Supports up to 64 DALI ballasts and 16 DALI groups per DALI channel
Supports up to 64 input devices overall per channel
Up to 16 DALI sensors per DALI channel are supported
Up to 64 DALI button modules per DALI channel are supported
Integrated DALI bus power supply
Manual operation using the jog dial and local access to information about device status and data points in clear text and symbols
128×64 graphic display with backlight
Built-in web server for device configuration
Test and assignment of DALI devices via the web interface
Replacement of DALI devices without additional software tools via LCD and jog dial
Supports the control of standard loads in the power grid via LDALI-RM3 Relay Modules
Integrated Constant Light Controller
Integrated Sunblind Controller
Supports DALI-2 devices (drivers and input devices)
DALI‑2 certified (compliant with IEC 62386‑101 and IEC 62386‑103)
Support DALI color control (DT8 tunable white & full color control)
Supports lamp burn-in mode
Supports periodic testing of DALI emergency lights
Integrated DALI Protocol Analyzer
Compliant with CEA‑709, CEA‑852 and ISO/IEC 14908-1 standard (LonMark System)
Network connection either with TP/FT‑10 or IP‑852 (CEA‑852 Ethernet)
Alarming, Scheduling, and Trending (AST) locally or embedded in L‑WEB (building management)
Node.js support for easy IoT integration (e.g. Google calendar, Alexa & friends, multimedia equipment,…)
Event-driven e-mail notification
Supports Local and Global Connections
Stores customized graphical pages
Visualization of customized graphical pages through LWEB‑900 (building Management), LWEB‑803 (Monitoring and Control), or LWEB‑802 (Web Browser)
Stores user-defined project documentation
Dual Ethernet/IP interface
Built-in OPC XML‑DA and OPC UA server
Modbus TCP (Master or Slave)
Supports SMI (Standard Motor Interface) through LSMI-804
Connection to EnOcean wireless devices via LENO‑80x Interface Supports WLAN through LWLAN‑800 Interface
Supports LTE through LTE‑800 Interface
Configurable Bluetooth beacons and services: indoor navigation, asset tracking (requires LIC-ASSET license) and access to LWEB-900 room control solution

Tutorials

L-DALI 7.4 Release Tutorial – Features of the new DALI Release

This video provides a detailed overview on the new features of the latest firmware release.

Features of L-INX 8.0 Release

This video presents several features of the new firmware release.

L-DALI: CEA-709/DALI Controllers Products

LDALI-3E101-U

CEA‑709/DALI Controller for IP-852 (Ethernet), 1 DALI channel, integrated DALI power supply

LDALI-3E102-U

CEA‑709/DALI Controller for IP-852 (Ethernet), 2 DALI channels, integrated DALI power supply

LDALI-3E104-U

CEA‑709/DALI Controller for IP-852 (Ethernet), 4 DALI channels, integrated DALI power supply

LIC-ASSET

LIC-ASSET, Add-on Software License to activate asset tracking (for LDALI-ME20x-U, LDALI-3E10x-U, LDALI-PLCx, LROC-400, LROC-401, LIOB-AIR20, LIOB-591)

Contact Sales for quote request

LDALI-PWR1-U

DALI Power Supply for 1 DALI channel, 50mA

LDALI-PWR2-U

DALI-2 power supply, 85-240 V, 50/60 Hz, Output: 2 x 16 VDC, 116 mA (DALI bus)

LDALI-PWR4-U

DALI-2 power supply, 85-240 V, 50/60 Hz, Output: 4 x 16 VDC, 116 mA (DALI bus)

LDALI-MS2-BT

DALI-2 multi-sensor (presence detection, illuminance sensor, IR receiver, temperature sensor, humidity sensor, 3 digital inputs, Bluetooth), up to 12 m mounting height

LDALI-MS4–BT

DALI-2 multi-sensor (presence detection, illuminance sensor, IR receiver, temperature sensor, humidity sensor, 3 digital inputs, Bluetooth, flat lens), up to 5 m mounting height

L-RC1

Infrared remote control for room automation applications

LDALI-PD1

DALI Phase-Cut Dimmer Module

LDALI-BM2

Quadruple DALI pushbutton coupler

LDALI-RM5

DALI Relay Module 10 A, Analog Interface 1 – 10 V

LDALI-RM6

DALI Relay Module 10 A, Analog Interface 1 – 10 V, “spud-mount”

LDALI-RM8

DALI Relay Modul, 8 channel

LSMI-804

Standard Motor Interface for 64 motors, 4 SMI channels via USB

LWLAN-800

Wireless LAN Interface IEEE 802.11bgn

LENO-800

EnOcean Interface 868 MHz Europe

LENO-801

EnOcean Interface 902 MHz USA/Canada

LENO-802

EnOcean Interface 928 MHz Japan

LTE-800

LTE Interface

LDALI-PWM4

PWM module, DALI, 4 x 3 A LED outputs, 24 V DC ext.

LDALI-PWM4-RGBW

PWM module RGBW, DALI, 4 x 3 A LED outputs, 24 V DC ext.

LDALI-PWM4-TC

PWM module tunable white, DALI, 4 x 3 A LED outputs, 24 V DC ext.

The post L-DALI: CEA-709/DALI Controllers appeared first on Kepler Electronics.

L-DALI: BACnet/DALI Controllers

Maen Sirhan — Tue, 02 Apr 2024 15:12:21 +0000

L-DALI:-ME201-U BACnet/DALI Controllers

LDALI-ME202-U BACnet/DALI Controller

LDALI-ME204-U BACnet/DALI Controller

L‑DALI Controllers are multifunctional devices combining constant light control, sunblind control and gateway functions between DALI (Digital Addressable Lighting Interface) and BACnet or Modbus systems. With Alarming, Scheduling, Trending and e-mail notification (AST) the L‑DALI Controller is a perfect solution for DALI lighting systems and for a smooth DALI integration into BACnet or Modbus networks.

DALI Network Interface

L-DALI Controllers act as a DALI-Master in the DALI network which can interact with DALI-2 multi-sensors and buttons in Multi-Master mode. The L-DALI Controllers feature 1, 2, or 4 independent DALI channels. Up to 64 DALI or DALI-2 based luminaries per DALI channel can be controlled individually or via 16 groups. All luminaries are monitored for lamp or ballast defect. In addition up to 64 DALI-2 input devices are supported per DALI channel. Each input device can be equipped with push buttons, sliders, occupancy and light sensors.

Built-In DALI Power Supply

All L-DALI models come with a built-in DALI bus power supply. The LDALI-ME201-U/LDALI-ME202-U can supply its DALI channel with a guaranteed supply current of 230 mA, the LDALI-ME204-U can supply 116 mA per channel. In case of the LDALI-ME204-U an external DALI bus power supply can be added to top up the supply current to 232 mA. External power supplies are available for up to four DALI channels. The internal DALI bus power can be switched on and off via web interface or LCD UI. Thanks to the switching power supply, these devices can handle input voltages from 85 – 240 V AC, 50/60 Hz.

BACnet Connectivity

The L‑DALI Controllers feature connectivity in BACnet networks via BACnet/IP, BACnet/SC or BACnet MS/TP. They also provide data exchange through Global Connections and support comprehensive AST functionality (Alarming, Scheduling, and Trending). Full L‑WEB integration is supported as well. The L‑DALI Controllers are equipped with two Ethernet ports including a built-in Ethernet switch.

IoT Integration

Local Operation and Override

Constant Light Control

The integrated Constant Light Controller works with DALI and with BACnet devices. It supports various lighting control strategies, presence and lux level based. Several parameters can be used to configure the Constant Light Controller for almost any use case.

Sunblind Control with Constant Light Control Interaction

The integrated Sunblind Controller application allows intelligent controlling of blinds connected via SMI (requires LSMI-804). It offers effective sun and anti-glare protection through active slat control and slat adjustment according to the sun position. Energy efficiency is ensured by linking room occupancy with sun protection. If a room is unoccupied, the L‑DALI Controller opens or closes the sunblinds depending on the thermal requirements. This allows for instance to use the heat of the sun for heating in winter while in summer, the heat from the sun is reduced by the closed blinds to reduce the cooling load.

Device Configuration via Tool or Web Interface

The device configuration, commissioning, and parameterization is done either with the configuration tool software or via the integrated web server.

EnOcean, OPC and Modbus

EnOcean sensors and buttons can be integrated via the optional L‑ENO EnOcean interface. To use the L‑DALI with an existing SCADA solution all run-time values and parameters can be accessed via BACnet, OPC (XML/DA and UA) and Modbus TCP. 5, 10 or 15 devices can be connected via Modbus RTU (RS-485), the actual number of supported devices is dependent on the activated licenses (LIC-MOD5, LIC-MOD10 or both).

Advanced DALI Functions

DALI Sensors
The L-DALI Controllers support the integration of DALI-2 multi-sensors for presence detection and light level recognition. In addition to the LOYTEC multi-sensors LDALI-MS2-BT/MS3-BT/MS4-BT, DALI-2 sensors of many well-known manufacturers can be used. For asset tracking in office buildings with the LOYTEC multi-sensors (LDALI-MSx-BT), a LIC-ASSET license is required.
DALI Buttons
For manual operation, DALI-2 push button couplers, like the LDALI-BM2, DALI-2 operation panels and IR remote controls can be integrated into the system. Their functionality can be configured individually. In addition to controlling lighting via DALI (dimming, scene recall, etc.) and sunblinds via SMI (up, down, etc.), button press events can be propagated in the building network, triggering other, non-lighting related building automation functions.
DALI Relay Modules
Standard loads in the power grid can be controlled via DALI using DALI relay modules, like the LDALI-RM5 / LDALI-RM6 /LDALI-RM8.
DALI Color Control
The L-DALI allows controlling DALI luminaires with color control functionality (DT8). Both, tunable white (Tc) and full RGB color control (RGBWAF and xycoordinate) are supported. Light color can either be changed automatically, via manual operation (e.g. buttons) or via the network.
Auto Burn-In for Fluorescent Lamps
Fluorescent lamps must be operated about 100 hours with 100 % brightness before they may be dimmed. This burn-in process is monitored by L‑DALI for each lamp. After 100 hours burn-in time, the lamp’s constant light control is enabled.
Automatic Test of Emergency Lighting Systems
IIn DALI emergency lighting systems based on IEC 62386-202, L-DALI can be used for testing the sys-tem. The results can be logged.
Collection of Important Operational Parameters
For maximum transparency in the lighting system, L‑DALI can record the operating hours of each lamp and also the energy consumption (calculated).
DALI Device Replacement made Easy
Defective DALI ballasts can easily be replaced directly on the L‑DALI Controller (LCD and jog dial) or via the web interface. No software tool is necessary.

Smooth DALI integration into BACnet and Modbus Networks

The L‑DALI Controller maps information from the DALI network to BACnet objects or Modbus registers that are used to control DALI ballasts or to display operating states.

BACnet Interface

The following BACnet server objects are supported:

Analog Output objects to control DALI ballasts, groups, and channels
Multi-State Output objects for scene control of DALI groups and channels Analog Input objects providing feedback from DALI ballast, groups, and channels
Analog Input objects providing status information from DALI groups and channels
Accumulator objects providing estimated energy usage of DALI groups and channels
Multi-State Output objects to issue commands (start/stop emergency test or burn-in, change color temperature, etc.) to DALI ballasts, groups and channels
Analog Input objects providing battery status of emergency ballasts, groups
Analog Input objects providing lux level information from supported DALI sensors
(LDALI-MS2: additionally humidity and temperature information is provided)
Binary Input objects providing occupancy information from supported DALI sensors
Loop objects providing constant light controller functionality
Binary Input objects providing button information from supported DALI buttons
Various objects to control sunblinds

All data points are available on the web server in a tree structure and can be displayed and set via a web browser.

Features

DALI integration into BACnet networks
Supports up to 64 DALI ballasts and 16 DALI groups per DALI channel
Supports up to 64 input devices overall per channel
Up to 16 DALI sensors per DALI channel are supported
Up to 64 DALI button modules per DALI channel are supported
Integrated DALI bus power supply
Manual operation using the jog dial and local access to information about device status and data points in clear text and symbols
128×64 graphic display with backlight
Built-in web server for device configuration
Test and assignment of DALI devices on the web interface
Replacement of DALI devices without additional software tools via LCD and jog dial
Supports the control of standard loads in the power grid via LDALI-RM3 Relay Modules
Integrated Constant Light Controller
Integrated Sunblind Controller
Supports DALI-2 devices (drivers and input devices)
DALI-2 certified (compliant with IEC 62386-101 and IEC 62386-103)
Support DALI color control (DT8 tunable white & full color control)
Supports lamp burn-in mode
Supports periodic testing of DALI emergency lights
Integrated DALI Protocol Analyzer
Compliant with ANSI/ASHRAE 135‑2012 and ISO 16484‑5:2012 standard
Supports BACnet MS/TP, BACnet/IP or BACnet/SC
BACnet Client Function (Write Property, Read Property, COV Subscription)
B-BC (BACnet Building Controller) functionality, BTL certified
Alarming, Scheduling, and Trending (AST) locally or embedded in L‑WEB (building management)
Node.js support for easy IoT integration (e.g. Google calendar, Alexa & friends, multimedia equipment,…)
Event-driven e-mail notification
Supports Local and Global Connections
Stores customized graphical pages
Visualization of customized graphical pages through LWEB‑900 (building Management), LWEB‑803 (Monitoring and Control), or LWEB‑802 (Web Browser)
Stores user-defined project documentation
Dual Ethernet/IP interface
Built-in OPC XML‑DA and OPC UA server
Modbus TCP or Modbus RTU/ASCII (Master or Slave)
Supports SMI (Standard Motor Interface) through LSMI-804
Connection to EnOcean wireless devices via LENO‑80x Interface
Supports WLAN through LWLAN‑800 Interface
Supports LTE through LTE‑800 Interface
Modbus RTU/ASCII for 5 devices (LIC-MOD5 required), 10 devices (LIC-MOD10 required) or 15 devices (LIC-MOD5 and LIC-MOD10 required)
Configurable Bluetooth beacons and services: indoor navigation, asset tracking (requires LIC-ASSET license) and access to LWEB-900 room control solution

Tutorials

L-DALI 7.4 Release Tutorial – Features of the new DALI Release

This video provides a detailed overview on the new features of the latest firmware release.

Features of L-INX 8.0 Release

This video presents some features of the newfirmware release.

L-DALI: BACnet/DALI Controllers Products

LDALI-ME201-U

BACnet/DALI Controller, 1 DALI channel, integrated DALI power supply

LDALI-ME202-U

BACnet/DALI Controller, 2 DALI channel, integrated DALI power supply

LDALI-ME204-U

BACnet/DALI Controller, 4 DALI channels, integrated DALI power supply

LIC-ASSET

LIC-ASSET, Add-on Software License to activate asset tracking (for LDALI-ME20x-U, LDALI-3E10x-U, LDALI-PLCx, LROC-400, LROC-401, LIOB-AIR20, LIOB-591)

Contact Sales for quote request

LIC-MOD5

License to add 5 Modbus devices for LDALI-ME201-U, LDALI-ME202-U, LDALI-ME204-U

LIC-MOD10

License to add 10 Modbus devices for LDALI-ME201-U, LDALI-ME202-U, LDALI-ME204-U

LDALI-PWR1-U

DALI Power Supply for 1 DALI channel, 50mA

LDALI-PWR2-U

DALI-2 power supply, 85-240 V, 50/60 Hz, Output: 2 x 16 VDC, 116 mA (DALI bus)

LDALI-PWR4-U

DALI-2 power supply, 85-240 V, 50/60 Hz, Output: 4 x 16 VDC, 116 mA (DALI bus)

LDALI-MS2-BT

DALI-2 multi-sensor (presence detection, illuminance sensor, IR receiver, temperature sensor, humidity sensor, 3 digital inputs, Bluetooth), up to 12 m mounting height

LDALI-MS4-BT

DALI-2 multi-sensor (presence detection, illuminance sensor, IR receiver, temperature sensor, humidity sensor, 3 digital inputs, Bluetooth, flat lens), up to 5 m mounting height

LDALI-PD1

DALI Phase-Cut Dimmer Module

L-RC1

Infrared remote control for room automation applications

LDALI-BM2

Quadruple DALI pushbutton coupler

LDALI-RM5

DALI Relay Module 10 A, Analog Interface 1 – 10 V

LDALI-RM6

DALI Relay Module 10 A, Analog Interface 1 – 10 V, “spud-mount”

LDALI-RM8

DALI Relay Modul, 8 channel

LSMI-804

Standard Motor Interface for 64 motors, 4 SMI channels via USB

LWLAN-800

EnOcean Interface 868 MHz Europe

LENO-801

EnOcean Interface 902 MHz USA/Canada

LENO-802

EnOcean Interface 928 MHz Japan

LTE-800

LTE Interface

LRS232-802

USB to 2x RS-232 Interface

LDALI-PWM4

PWM module, DALI, 4 x 3 A LED outputs, 24 V DC ext

LDALI-PWM4-RGBW

PWM module RGBW, DALI, 4 x 3 A LED outputs, 24 V DC ext.

LDALI-PWM4-TC

PWM module tunable white, DALI, 4 x 3 A LED outputs, 24 V DC ext.

The post L-DALI: BACnet/DALI Controllers appeared first on Kepler Electronics.

LDALI‑PLC2 LDALI‑PLC4: Programmable DALI Controller

Maen Sirhan — Fri, 29 Mar 2024 09:15:08 +0000

Product available through Competence Partner Program
L-FOCUS: L-DALI Lighting Control Solutions (English)
LDALI-PLC2/PLC4 Datasheet
L-DALI User Manual
LDALI-PLC2/PLC4 Installation Instructions
L-DALI Compatibility List
Certificates: EC / BTL / DALI-2 / AMEV
Downloads: LDALI-PLC2 / LDALI-PLC4

The LDALI‑PLC2/PLC4 controllers are powerful, programmable lighting controllers, which can be programmed by L‑STUDIO. With Alarming, Scheduling, Trending and e‑mail notification (AST) the LDALI‑PLC2/PLC4 controller is a perfect solution for DALI lighting systems with application requirements not covered by the standard application of the non‑programmable L‑DALI controllers.

DALI Network Interface

L‑DALI Controllers act as a DALI‑Master in the DALI network and can interact withDALI‑2 multi‑sensors and buttons in Multi‑Master mode. The LDALI‑PLC2/PLC4 is equipped with 2/4 independent DALI channels. Up to 64 DALI or DALI‑2 basedluminaries per DALI channel can be controlled individually or via 16 groups. Allluminaries are monitored for lamp or ballast defect. In addition up to 64 DALI‑2input devices are supported per DALI channel. Each input device can be equipped with push buttons, sliders, occupancy and light sensors.

Built-In DALI Bus Power Supply

The LDALI‑PLC4 comes with a built‑in DALI bus power supply, which can supply each DALI channel with a guaranteed supply current of 116 mA. An external DALI bus power supply can be added to top up the supply current to 232 mA. External power supplies are available for up to four DALI channels. The LDALI‑PLC2 pro‑vides a DALI‑bus power supply with guaranteed supply current of 230mA per channel. The internal DALI bus power can be switched on and off via web interface or LCD UI. Thanks to the switching power supply, these devices can handle input voltages from 85 – 240 V AC, 50/60 Hz.

Local Operation and Override

The L‑DALI Controllers come with a built‑in backlit display (128×64) and a jog dial for local operation and override. Using the local operation, maintenance tasks (DALI device replacement, burn‑in mode, etc.) can be executed without the need of any software tool.

Programmable

The LDALI‑PLC2/PLC4 can be programmed using the L‑STUDIO programming tool. It can be programmed using IEC 61499 for integration into the L‑ROC system and IEC 61131 for stand-alone operation.

IEC 61131 lighting control library available

A library containing standard lighting control functionality is available. It supports various lighting control strategies, presence and lux level based. Several parame‑ters can be used to configure the application for almost any use case. User specific program extensions are possible as well.

Connectivity

The LDALI‑PLC2/PLC4 controller provides connectivity functions to concurrently integrate CEA‑709 (LonMark Systems), BACnet, KNX, and Modbus subsystems. LonMark Systems can be integrated via IP‑852 (Ethernet/IP). BACnet integration is supported through BACnet/IP (Ethernet/IP), BACnet/SC or BACnet MS/TP (RS‑485), KNXnet/IP and Modbus TCP via Ethernet/IP.

The gateway functionality allows data communication between all communication technologies available on the device. Different technology data points are mapped through Local Connections on the device. The mapping of different technology data points on distributed devices is supported by Global Connections.

Each L-DALI Controller is equipped with two Ethernet ports. It can either be configured to use the internal switch to interconnect the two ports or every port is configured to work in a separate IP network.

When the Ethernet ports are configured for two separate IP networks, one port can be connected for instance to a WAN (Wide Area Network) with enabled network security (HTTPS) while the second port can be configured to be connected to an insecure network (LAN) where the standard building automation protocols like BACnet/IP, LON/IP, or Modbus TCP are present. These devices also feature firewall functionality to isolate particular protocols or services between the ports.

Using the internal switch, a daisy chained line topology of up to 20 devices can be built, which reduces costs for network installation. The IP switch also allows the setup of a redundant Ethernet installation (ring topology), which increases reliability. The redundant Ethernet topology is enabled by the Rapid Spanning Tree Protocol (RSTP), which is supported by most managed switches.

The L-DALI Controllers provide fully featured AST functionality (Alarming, Scheduling, and Trending) and can be integrated perfectly into the L‑WEB System.

IoT Integration

Device Configuration via Tool or Web Interface

The device configuration, commissioning, and parameterization is done either with the configuration tool software or via the integrated web server.

EnOcean, SMI and LIOB/‌IP

Wireless EnOcean sensors and buttons can be integrated via the optional L‑ENO EnOcean interface. For sunblinds the LSMI-804 extension module allows the integration of up to four SMI channels. Physical I/Os can be integrated through L‑IOB I/O Modules via LIOB‑IP.

Advanced DALI Functions

DALI Sensors
The L-DALI Controllers support the integration of DALI-2 multi-sensors for presence detection and light level recognition. In addition to the LOYTEC multi-sensors LDALI‑MS2-BT/MS3‑BT/MS4‑BT, DALI-2 sensors of many well-known manufacturers can be used.
DALI Buttons
For manual operation, DALI-2 push button couplers, like the LDALI-BM2, DALI-2 operation panels, and IR remote controls can be integrated into the system. The function executed when a button is pressed is freely programmable in the program logic. In addition the feedback feature for pushbutton instances according to IEC 62386‑332 is supported.
DALI Relay Modules
Standard loads in the power grid can be controlled via DALI using DALI relay modules, like the LDALI-RM5, LDALI-RM6 and LDALI-RM8.
DALI Color Control
The LDALI allow controlling DALI luminaires with color control functionality (DT8). Both, tunable white (Tc) and full RGB color control (RGBWAF and xy-coordinate) are supported. Changing the light colour is possible via scenes or controlled via the program logic.
Auto Burn-In for fluorescent Lamps
Fluorescent lamps must be operated about 100 hours with 100 % brightness before they may be dimmed. This burn-in process is monitored by L‑DALI for each lamp. After 100 hours burn-in time, the lamp’s constant light control is enabled.
Automatic Test of Emergency Lighting Systems
In DALI emergency lighting systems based on IEC 62386-202, L-DALI can be used for testing the system. The results can be logged.
Collection of important operational Parameters
For maximum transparency in the lighting system, L‑DALI can record the operating hours of each lamp and also the energy consumption (calculated).
DALI Device Replacement made easy
Defective DALI ballasts can easily be replaced directly on the L‑DALI Controller (LCD and jog dial) or via the web interface. No software tool is necessary.

Features

Programmable with L‑STUDIO IEC 61131‑3 and IEC 61499
Supports up to 64 DALI ballasts and 16 DALI groups per DALI channel
Supports up to 64 input devices overall per channel
Up to 16 DALI sensors per DALI channel are supported
Up to 64 DALI button modules per DALI channel are supported
Integrated DALI bus power supply
DALI‑2 certified
Manual operation using the jog dial and local access to information about device status and data points in clear text and symbols
128×64 graphic display with backlight
Built‑in web server for device configuration
Test and assignment of DALI devices on the web interface
Replacement of DALI devices without additional software tools via LCD and jog dial
Supports the control of standard loads in the power grid via LDALI‑RM5/RM6/RM8 Relay Modules
Supports DALI‑2 devices (drivers and input devices)
Support DALI color control (DT8 tunable white & full color control)
Supports lamp burn‑in mode
Supports periodic testing of DALI emergency lights
Integrated DALI Protocol Analyzer
Physical inputs and outputs with L‑IOB I/O Modules
Compliant with CEA‑709, CEA‑852, and ISO/IEC 14908 Standard (LonMark System)
Support of dynamically created or static NVs
Support of user‑defined NVs (UNVTs) and Configuration Properties (SCPTs, UCPTs)
KNXnet/IP
Gateway functions including Smart Auto‑Connect
Modbus TCP and Modbus RTU/ASCII
Compliant with ANSI/ASHRAE135‑2012 and ISO16484‑5:2012 standard
Supports BACnet MS/TP, BACnet/IP or BACnet/SC
BACnet Client Function (Write Property, Read Property, COV Subscription)
B‑BC (BACnet Building Controller) functionality, BTL certified
Alarming, Scheduling, and Trending (AST) locally or embedded in L‑WEB (building management)
Node.js support for easy IoT integration (e.g. Google calendar, Alexa & friends, multimedia equipment,…)
Event‑driven e‑mail notification
Supports Local and Global Connections
Built‑in OPCXML‑DA and OPCUA server
Stores customized graphical pages
Visualization of customized graphical pages through LWEB‑900 (building Management), LWEB‑803 (Monitoring and Control), or LWEB‑802 (Web Browser)
Stores user‑defined project documentation
Dual Ethernet/IP interface
Supports SMI (Standard Motor Interface) through LSMI‑804
Connection to EnOcean wireless devices via LENO‑80x Interface
Supports WLAN through LWLAN‑800 Interface
Supports LTE through LTE‑800 Interface
Configurable Bluetooth beacons and services: indoor navigation, asset tracking (requires LIC-ASSET license) and access to LWEB-900 room control solution

Tutorials

Light Library Tutorial

The video shows basic steps on how to create a light application with the LDALI-PLC2/PLC4 in L-STUDIO.

L-DALI 7.4 Release Tutorial – Features of the new DALI Release

This video provides a detailed overview on the new features of the latest firmware release.

Features of L-INX 8.0 Release

This video presents some features of the new firmware release.

LDALI‑PLC2 / LDALI‑PLC4: Programmable DALI Controller Products

LDALI-PLC2

Programmable DALI Controller, 2 DALI channels, integrated DALI power supply

LDALI-PLC4

Programmable DALI Controller, 4 DALI channels, integrated DALI power supply

L-STUDIO

Device configuration and programming suite

LIC-ASSET

LIC-ASSET, Add-on Software License to activate asset tracking (for LDALI-ME20x-U, LDALI-3E10x-U, LDALI-PLCx, LROC-400, LROC-401, LIOB-AIR20, LIOB-591)

Contact Sales for quote request

LOY-DALI-SBM1

LOY-DALI-SBM1 Sunblind Module

LDALI-PWR1-U

DALI Power Supply for 1 DALI channel, 50mA

LDALI-PWR2-U

DALI-2 power supply, 85-240 V, 50/60 Hz, Output: 2 x 16 VDC, 116 mA (DALI bus)

LDALI-PWR4-U

DALI-2 power supply, 85-240 V, 50/60 Hz, Output: 4 x 16 VDC, 116 mA (DALI bus)

LDALI-MS2-BT

DALI-2 multi-sensor (presence detection, illuminance sensor, IR receiver, temperature sensor, humidity sensor, 3 digital inputs, Bluetooth), up to 12 m mounting height

LDALI-MS4-BT

DALI-2 multi-sensor (presence detection, illuminance sensor, IR receiver, temperature sensor, humidity sensor, 3 digital inputs, Bluetooth, flat lens), up to 5 m mounting height

LDALI-BM2

Quadruple DALI pushbutton coupler

LDALI-RM5

DALI Relay Module 10 A, Analog Interface 1 – 10 V

LDALI-RM6

DALI Relay Module 10 A, Analog Interface 1 – 10 V, “spud-mount”

LDALI-RM8

DALI Relay Modul, 8 channel

LDALI-PD1

DALI Phase-Cut Dimmer Module

LWLAN-800

Wireless LAN Interface IEEE 802.11bgn

LENO-800

EnOcean Interface 868 MHz Europe

LENO-801

LENO-802

EnOcean Interface 928 MHz Japan

LRS232-802

USB to 2x RS-232 Interface

LSTAT-810-G3-L0

Remote EnOcean Antenna, Europe, White

LSTAT-820-G3-L0

Remote EnOcean Antenna, USA/CA, White

LSTAT-830-G3-L0

Remote EnOcean Antenna, Japan, White

LSMI-804

Standard Motor Interface for 64 motors, 4 SMI channels via USB

LTE-800

LTE Interface

L-RC1

Infrared remote control for room automation applications

LDALI-PWM4

PWM module, DALI, 4 x 3 A LED outputs, 24 V DC ext.

LDALI-PWM4-TC

PWM module tunable white, DALI, 4 x 3 A LED outputs, 24 V DC ext.

LDALI-PWM4-RGBW

LSTAT-810-GX-LX-CU

LSTAT-800 based custom design, includes EnOcean interface, minimum quantity 100 pcs, enclosure G1: silver, G2: black, G3: white; custom print Lx, including 2 working samples, lead time 10 weeks (needs LSTAT-80x-CUSTOM)

LSTAT-812-GX-LX-CU

LSTAT-802 based custom design, includes EnOcean interface, minimum quantity 100 pcs, enclosure G1: silver, G2: black, G3: white; custom print Lx, including 2 working samples, lead time 10 weeks (needs LSTAT-80x-CUSTOM)

LSTAT-80x-CUSTOM

One-time customization cost for L-STAT custom design, including 2 working samples

The post LDALI‑PLC2 LDALI‑PLC4: Programmable DALI Controller appeared first on Kepler Electronics.

KDALI-GW1i

Maen Sirhan — Thu, 19 Oct 2023 13:34:38 +0000

KDALI Gateway KDALI-GW1i

This product supports up to 250mA DALI PS, 64 DALI control gears, enables broadcast control, single lamp single
control, group control and other different ways of control and supports timing, scene and other linkage control method.
It is connected via Ethernet (RJ45 network cable), and the link between the mobile phone and the gateway is not
affected by the signal. As long as the mobile phone and the gateway are under the same network, it can be controlled.

Key Features:

Supports DT6, DT8 Tc, DT8 XY, DT8 RGBWAF device types
No need for DALI master controller supports up to 64 devices addressing,
grouping and scene setting.
Built-in 250mA DALI PS, no extra wiring required
Easy connect to a network through Ethernet connection
Easy & quick configuration through the mobile application
Built-in battery, built-in RTC, supports timer task configuration
Supports cycle schedule configuration

The post KDALI-GW1i appeared first on Kepler Electronics.

LROC-102 Room Controller

Maen Sirhan — Sun, 08 Oct 2023 21:38:08 +0000

Product available through Competence Partner Program
LROC-102 Datasheet
LROC-102 Installation Instructions
L-ROC User Manual
Certificates: EC / BTL / UL / AMEV
Downloads

The L-ROC Room Controller provides the basis for a revolutionary room automation system based on IP, which seamlessly integrates with native BACnet/IP networks and LonMark Systems at the controller level. Together with the L-STUDIO software flexible room solutions can be created with little effort and changed on demand. An integral part of the L-ROC System is a Web based room operation via an LWEB‑803/802 dashboard and the automatic generation of graphics for the L-VIS Touch Panel for local operation. For CEA‑709 room control units, CEA‑709 multi-sensors and other CEA‑709 devices can be connected via the LonMark TP/FT-10 channel on the L-ROC controller. Local inputs and outputs are provided via L-IOB I/O Modules. KNX S-mode devices can be connected through KNX TP1 by using the optional LKNX-300 module.

Flexible Room Concept for Room Automation

A room segment is the base unit of configuration in the L-ROC System. The L-ROC Library provides a set of functions for every window axis including:

Lighting control with constant light controller
Sun blind control with angle adjustment and year shade progression
Temperature control for heating, cooling, and ventilation
Occupancy detection
Window monitoring

Each L-ROC Room Controller can handle up to 16 room segments. Based on the various room segment types, larger buildings can be modeled in a hierarchical manner. Areas are built with an area manager by combining multiple room controllers. A floor manager manages multiple areas in one floor. Depending on the architecture, the building can be split up into areas and floors as needed.

Area/Floor Managers are responsible for handling functions needed for corridor, staircase, and bathroom lighting, or even ventilation. Floor managers facilitate the data communication between the floors and handle floor relevant functions.

Rooms can now be created arbitrarily in any size by moving, building, or removing partition walls. The resulting logical connections between the L-ROC Room Controllers will be built automatically. All graphical user interfaces and network connections are automatically generated and adapted respectively.

AST for Every Room Segment

L-ROC provides a set of functions for Alarming, Scheduling, and Trending (AST) for every room segment. Each room segment can be operated entirely independently. The AST functions are fully available to higher-level systems through BACnet/IP and Web services (L-WEB System). Distributed schedulers can be efficiently managed and changed with LWEB-900.

Room Communication through redundant or separated IP Network

L‑ROC Room Controllers are interconnected via a 100Base-T Ethernet network. Each L-ROC device is equipped with two Ethernet ports. It can either be configured to use the internal switch to interconnect the two ports or every port is configured to work in a separate IP network.

When the Ethernet ports are configured for two separate IP networks, one port can be connected for instance to a WAN (Wide Area Network) with enabled network security (HTTPS) while the second port can be configure to be connected to an insecure network (LAN) where the standard building automation protocols like BACnet/‌IP, LON/‌IP, or Modbus TCP are present. These devices also feature firewall functionality of course to isolate particular protocols or services between the ports.

Using the internal switch, a daisy chained line topology of up to 20 devices can be built, which reduces costs for network installation. The IP switch also allow the setup of a redundant Ethernet installation (ring topology), which increases reliability. The redundant Ethernet topology is enabled by the Rapid Spanning Tree Protocol (RSTP), which is supported by most managed switches.

Integrated L-WEB Room Operation

L-ROC controllers provide graphical user interfaces for room operation directly via an IP connection to the user, without the need for an additional web server. Graphic projects are distributed among the L-ROC Room Controllers and can be accessed by LWEB‑802/‌803 from any PC workstation, smart phone, or tablet PC running Android or iOS.

Integration of the L-STAT Network Thermostat

Per L-ROC Room Controller up to 16 L-STAT room control devices can be integrated into building automation via Modbus RTU (RS-485) interface. In addition to the attractive, modern design and intuitive operation, L-STAT provides a range of other features to individually increase the room comfort.

Internal sensors measure temperature, humidity, condensation, occupancy, and also the CO₂ value of the air. There is also the possibility to control room functions from remote via an IR remote control. Standard pushbuttons and external temperature sensors can be integrated through additional inputs.

Connection to Higher-Level Systems

Higher-level systems can seamlessly integrate L-ROC Room Controllers via BACnet/IP, LonMark IP-852, or Web services (OPC).

All these protocols are simultaneously available. It is possible to integrate the L-ROC Room Controller in a BACnet Operator Workstation and at the same time L‑ROC will communicate with other CEA‑709 devices on the IP-852 channel. Moreover, a higher-level SCADA or ERP System (Facility Management) gets information directly from the L-ROC Room Controller by using Web services based on OPC.

Full LWEB-900 Support

The L-WEB System uses Web services to communicate with the L-ROC System. All device and operating parameters of every single L-ROC Room Controller are automatically synchronized with the LWEB-900 SQL database by the LWEB-900 client or the LWEB‑900 Master Device Manager. The parameters are available to all L-WEB client applications.

I/O Integration via Plug and Play

The L‑ROC Room Controllers can automatically integrate physical I/Os by using L-IOB I/O Modules. Up to 24 L-IOB I/O Modules can be connected through LIOB‑Connect, LIOB-FT, or LIOB-IP. All I/Os can be used by the L-ROC application and are also available via the Web interface of L-ROC. All configurations of the L-IOB Modules are stored on the L-ROC and loaded on demand into the L-IOB I/O Modules. Exchanging I/O modules is done without any configuration effort requiring only a few quick configuration steps.

Year Shade Progression

Especially in dense city areas, buildings can cast shadows on each other. In case a façade element is shaded by another building, sunblinds can be deactivated for better daylight harvesting. The high-performance L-ROC controllers allow to calculate a 3D model in dxf-Format of the building and its close-by neighbors. The model can be constructed using common 3D CAD software or can be derived from a Building Information Model. In case the scenery changes due to new constructions, only the new buildings have to be inserted in the model. The calculation can be done for each window individually or per shadowing zone.

IoT Integration

Features

Flexible built-in management for room segments
Room controller for up to 16 room segments
Networking via redundant or separated IP network
Programmable with L‑STUDIO (IEC 61499)
Extension with physical inputs and outputs using L‑IOB I/ O Modules (LIOB‑11x, LIOB‑15x, and LIOB‑45x/55x)
128×64 graphic display with backlight
Local display of device and data point information
Manual operation using the jog dial or VNC Client
Integrated AST functions (Alarming, Scheduling, and Trending) for each room segment
Node.js support for easy IoT integration (e.g. Google calendar, Alexa & friends, multimedia equipment,…)
Event-driven e-mail notification Math objects to execute mathematical operations on data points
Stores customized graphical pages
Visualization of customized graphical pages through LWEB‑900 (Building Management), LWEB‑803 (Monitoring and Control), or LWEB‑802 (Web Browser)
Support of the L‑STAT Room Operator Panel
Built-in OPC XML‑DA and OPC UA server
Dual Ethernet/ IP interface
Access to network statistics
Compliant with ANSI/ ASHRAE 135‑2012 and ISO 16484‑5:2012 standard
Supports BACnet MS/TP, BACnet/IP or BACnet/SC
BACnet Client Function (Write Property, Read Property, COV Subscription)
BACnet Client Configuration with configuration tool (scan and EDE import)
BACnet/ IP compliant with B-BC (BACnet Building Controller) functionality
Compliant with CEA‑709, CEA‑852, and ISO/ IEC 14908 Standard (LonMark System)
Connection of any CEA‑709 device via TP/ FT‑10 channel
CEA‑709 integration via LonMark IP‑852 (Ethernet/ IP) channel
Support of dynamically created or static NVs
Support of user-defined NVs (UNVTs) and Configuration Properties (SCPTs, UCPTs)
Integrated BACnet/ IP to BACnet/SC and BACnet MS/ TP Router including BBMD as well as Slave-Proxy functionality
Integrated IP‑852 to TP/FT‑10 Router
Connection to KNXnet/ IP directly, KNX TP1 via LKNX‑300 Interface
M‑Bus Master according to EN 13757‑3, connection via optional M‑Bus Converter (L‑MBUS20 or L‑MBUS80)
Gateway functions including Smart Auto-Connect
Modbus TCP and Modbus RTU/ASCII (Master or Slave)
Integrated web server for device configuration and monitoring data points
Configurable via Ethernet/ IP
Connection to EnOcean wireless devices via LENO‑80x Interface
Supports WLAN through LWLAN‑800 Interface
Supports MP-Bus through LMPBUS-804 Interface
Supports SMI (Standard Motor Interface) through LSMI-80x
Supports LTE through LTE-800 Interface
Stores user-defined project documentation

L-ROC Room Automation – Video

LROC-102 Room Controller Products

LROC-102

L-ROC Room Controller for room segment, aisle, floor, building, or campus management

LROC-SEG8

License to add 8 segments to L-ROC controller

L-STUDIO

Device configuration and programming suite

LSTAT-80x-CUSTOM

One-time customization cost for L-STAT custom design, including 2 working samples

LIOB-A2

L‑IOB Adapter 2 to split the LIOB‑Connect bus using 4-wire cables

LIOB-A4

L‑IOB Adapter 4 to split the LIOB‑Connect bus using RJ45 network cables

LIOB-A5

L‑IOB Adapter 5 to terminate the LIOB-Connect bus

LIOB-100

LIOB-Connect I/O Module: 8 UI, 2 DI, 2 AO, 9 DO (5 x Relay 6 A, 4 x Triac 0.5 A)

LIOB-101

LIOB-Connect I/O Module: 8 UI, 16 DI

LIOB-102

LIOB-Connect I/O Module: 6 UI, 6 AO, 5 DO (5 x Relay 16 A)

LIOB-110

LIOB-Connect I/O Module: 20 Universal I/O (IO)

LIOB-112

LIOB-FT I/O Module: 8 UI, 2 DI, 2 AO, 8 DO (4 x Relay 6 A, 4 x Triac 0.5 A)

LIOB-151

LIOB-FT I/O Module: 8 UI, 12 DI

LIOB-152

LIOB-FT I/O Module: 6 UI, 6 AO, 8 DO (8 x Relay 6 A)

LIOB-153

LIOB-FT I/O Module: 6 UI, 6 AO, 5 DO (4 x Relay 16 A, 1 x Relay 6 A)

LIOB-154

LIOB-FT I/O Module: 7 UI, 4 AO, 7 DO (5 x Relay 6 A, 2 x Triac 0.5 A), 1 Pressure Sensor

LIOB-450

LIOB-IP852 I/O Module: 8 UI, 2 DI, 2 AO, 8 DO (4 x Relay 6 A, 4 x Triac 0.5 A)

LIOB-451

LIOB-IP852 I/O Module: 8 UI, 12 DI

LIOB-452

LIOB-IP852 I/O Module: 6 UI, 6 AO, 8 DO (8 x Relay 6 A)

LIOB-453

LIOB-IP852 I/O Module: 6 UI, 6 AO, 5 DO (4 x Relay 16 A, 1 x Relay 6 A)

LIOB-454

LIOB-IP852 I/O Module: 7 UI, 4 AO, 7 DO (5 x Relay 6 A, 2 x Triac 0.5 A), 1 Pressure Sensor

LIOB-550

LIOB-BIP I/O Module: 8 UI, 2 DI, 2 AO, 8 DO (4 x Relay 6 A, 4 x Triac 0.5 A)

LIOB-551

LIOB-BIP I/O Module: 8 UI, 12 DI

LIOB-552

LIOB-BIP I/O Module: 6 UI, 6 AO, 8 DO (8 x Relay 6 A)

LIOB-553

LIOB-BIP I/O Module: 6 UI, 6 AO, 5 DO (4 x Relay 16 A, 1 x Relay 6 A)

LIOB-554

LIOB-BIP I/O Module: 7 UI, 4 AO, 7 DO (5 x Relay 6 A, 2 x Triac 0.5 A), 1 Pressure Sensor

LPOW-2415A

LIOB-Connect Power Supply, 24 VDC, 15 W

LPOW-2415B

Power supply unit with power connector 24 VDC, 15 W

LSMI-800

Standard Motor Interface for 16 motors via EXT port

L-MBUS20

M-Bus level converter, interface for 20 M-Bus devices

L-MBUS80

M-Bus Level Converter, Interface for up to 80 M-Bus devices

LKNX-300

KNX interface to connect KNX TP1 devices

LENO-800

EnOcean Interface 868 MHz Europe

LENO-801

EnOcean Interface 902 MHz USA/Canada

LENO-802

EnOcean Interface 928 MHz Japan

LWLAN-800

Wireless LAN Interface IEEE 802.11bgn

LRS232-802

USB to 2x RS-232 Interface

LBOX-600

L-BOX System Distribution Box for room automation components, 600 x 250 x 82 (L x W x H in mm)

LSTAT-810-G3-L0

Remote EnOcean Antenna, Europe, White

LSTAT-820-G3-L0

Remote EnOcean Antenna, USA/CA, White

LSTAT-830-G3-L0

Remote EnOcean Antenna, Japan, White

LIOB-560

LIOB-BIP I/O Modul: 20 Universal I/O (IO)

LIOB-562

LIOB-BIP I/O Module: 40 Universal I/O (12 optionally with 4-20 mA Current Output)

The post LROC-102 Room Controller appeared first on Kepler Electronics.

LIOB-591 Room Controller

Maen Sirhan — Sun, 08 Oct 2023 21:28:02 +0000

The LIOB‑591 fan coil controller provides the basis for a revolutionary room automation system based on IP, which seamlessly integrates with native BACnet/IP networks at the controller level. Together with the L‑STUDIO software, room control solutions can be created with little effort. Integral parts of the room control system are a web‑based room operation via an LWEB‑802/803 dashboard and the automatic generation of graphics for the L‑VIS Touch Panel for local operation. LIOB‑591 Controllers implement the BACnet Building Controller (B-BC) profile and are BTL certified.

Our room controllers provide all common interfaces and a large number of physical I/Os for room automation projects. DALI lamps and DALI sensors are connected to the DALI interface with an integrated DALI power supply. Up to 16 SMI sunblind motors connect to an external SMI interface. Belimo valves connect to the external MP‑Bus interface. BACnet MS/TP devices connect to the RS‑485 interface, which can also be configured as a Modbus RTU interface to connect Modbus devices like energy meters or ekey finger scanners for access control or to connect the L‑STAT Room Control Unit. EnOcean devices connect to the external EnOcean interface. Dual Ethernet ports allow daisy-chaining of LIOB-591 controllers in a ring topology and provide BACnet/IP, Modbus/IP and OPC communication.

Optionally, the LIOB-591 can communicate via wireless LAN through the LWLAN‑800 wireless adapter connected to the USB port. 20 universal I/Os, one 1250 W and three 300 W TRIAC outputs connect various physical input and output devices. Our room automation library provides pre-built function modules for all lighting, heating, cooling, ventilation, sunblinds and access control via finger scanners. Built‑in SSL encryption ensures secure operation of the room automation system.

All typical room functions are supported:

Lighting control with constant light controller
Sunblind control with angle adjustment and year shade progression
Temperature control for heating, cooling, and ventilation
Occupancy detection
Window monitoring and window contact

Features

Room controller for 1 room segment
Networking via redundant IP network
Programmable with L-STUDIO (IEC 61131-3 or IEC 61499)
Extension with physical inputs and outputs using L‑IOB I/O Modules (LIOB‑45x or LIOB‑55x)
128×64 graphic display with backlight for device configuration and maintenance
Local display of device and data point information
Manual operation using the jog dial or VNC Client
Integrated AST functions (Alarming, Scheduling, and Trending) for each room segment
Node.js support* for easy IoT integration (e.g. Google calendar, Alexa & friends, multimedia equipment,…)
Event-driven e-mail notification
Math objects to execute mathematical operations on data points
Stores customized graphical pages
Visualization of customized graphical pages through LWEB‑900 (Building Management), LWEB‑803 (Monitoring and Control), or LWEB‑802 (Web Browser)
Support of the L‑STAT Room Operator Panel
Built-in OPC XML‑DA and OPC UA server
Access to network statistics via SNMP
Compliant with ANSI/ ASHRAE 135‑2012 and ISO 16484‑5:2012 standard
Supports BACnet MS/TP, BACnet/IP or BACnet/SC
BACnet Client Function (Write Property, Read Property, COV Subscription)
BACnet Client Configuration with configuration tool (scan and EDE import)
B-BC (BACnet Building Controller) functionality, BTL certified
Integrated BACnet/ IP to BACnet/SC and BACnet MS/ TP
Router including BBMD as well as Slave-Proxy functionality
Modbus TCP and Modbus RTU/ASCII (Master or Slave)
Integrated web server for device configuration and monitoring data points
DALI integration of up to 64 DALI lamps
Integrated DALI power supply, 16 V DC, 116 mA max. current
Integrated 1250 W heater control
Integrated dual fan motor control
8 x Universal I/O (U, I, R), 12 x Universal I/O (U)**
Integrated heating/cooling valve control
Configurable Bluetooth beacons and services: indoor navigation, asset tracking (requires LIC-ASSET license) and access to LWEB-900 room control solution

*requires L-IOT1 software license
**U: 0-10V input or 0-10V output, I: 4-20 mA input, R: resistance measurement

LIOB-591 Room Controller Products

LIOB-591

L-IOB Room Controller, 8x Universal I/O (U, I, R), 12x Universal I/O (U), 1x TRIAC 1250W, 3x TRIAC 300W

L-IOT1

Add-on Software License to enable IoT functionality on LIOB-585/586/587/588/589, LIOB-590/591/592/593/594/595/596, LIOB-AIR, and LINX-102/103/202/203

L-STUDIO

Device configuration and programming suite

LENO-800

EnOcean Interface 868 MHz Europe

LENO-801

EnOcean Interface 902 MHz USA/Canada

LENO-802

EnOcean Interface 928 MHz Japan

LSTAT-810-G3-L0

Remote EnOcean Antenna, Europe, White

LSTAT-820-G3-L0

Remote EnOcean Antenna, USA/CA, White

LSTAT-830-G3-L0

Remote EnOcean Antenna, Japan, White

LWLAN-800

Wireless LAN Interface IEEE 802.11bgn

LTE-800

LTE Interface

LMPBUS-804

MP-Bus Interface for 16 devices per channel, up to 4 channels

LSMI-804

Standard Motor Interface for 64 motors, 4 SMI channels via USB

LRS232-802

USB to 2x RS-232 Interface

L-TEMP2

External temperature sensor (NTC10K) for use with L-IOB Universal Inputs

LDALI-MS2-BT

DALI-2 multi-sensor (presence detection, illuminance sensor, IR receiver, temperature sensor, humidity sensor, 3 digital inputs, Bluetooth), up to 12 m mounting height

LDALI-MS4-BT

DALI-2 multi-sensor (presence detection, illuminance sensor, IR receiver, temperature sensor, humidity sensor, 3 digital inputs, Bluetooth, flat lens), up to 5 m mounting height

LIC-ASSET

LIC-ASSET, Add-on Software License to activate asset tracking (for LDALI-ME20x-U, LDALI-3E10x-U, LDALI-PLCx, LROC-400, LROC-401, LIOB-AIR20, LIOB-591)

Contact Sales for quote request

L-RC1

Infrared remote control for room automation applications

LOY-DALI-SBM1

LOY-DALI-SBM1 Sunblind Module

LDALI-BM2

Quadruple DALI pushbutton coupler

LDALI-RM5

DALI Relay Module 10 A, Analog Interface 1 – 10 V

LDALI-RM6

DALI Relay Module 10 A, Analog Interface 1 – 10 V, “spud-mount”

LDALI-RM8

DALI Relay Modul, 8 channel

LDALI-PWM4

PWM module, DALI, 4 x 3 A LED outputs, 24 V DC ext.

LDALI-PWM4-TC

PWM module tunable white, DALI, 4 x 3 A LED outputs, 24 V DC ext.

LDALI-PWM4-RGBW

PWM module RGBW, DALI, 4 x 3 A LED outputs, 24 V DC ext.

LDALI-PD1

DALI Phase-Cut Dimmer Module

LSTAT-810-GX-LX-CU

LSTAT-812-GX-LX-CU

LSTAT-80x-CUSTOM

One-time customization cost for L-STAT custom design, including 2 working samples

LIOB-450

LIOB-IP852 I/O Module: 8 UI, 2 DI, 2 AO, 8 DO (4 x Relay 6 A, 4 x Triac 0.5 A)

LIOB-451

LIOB-IP852 I/O Module: 8 UI, 12 DI

LIOB-452

LIOB-IP852 I/O Module: 6 UI, 6 AO, 8 DO (8 x Relay 6 A)

LIOB-453

LIOB-IP852 I/O Module: 6 UI, 6 AO, 5 DO (4 x Relay 16 A, 1 x Relay 6 A)

LIOB-454

LIOB-IP852 I/O Module: 7 UI, 4 AO, 7 DO (5 x Relay 6 A, 2 x Triac 0.5 A), 1 Pressure Sensor

LIOB-550

LIOB-BIP I/O Module: 8 UI, 2 DI, 2 AO, 8 DO (4 x Relay 6 A, 4 x Triac 0.5 A)

LIOB-551

LIOB-BIP I/O Module: 8 UI, 12 DI

LIOB-552

LIOB-BIP I/O Module: 6 UI, 6 AO, 8 DO (8 x Relay 6 A)

LIOB-553

LIOB-BIP I/O Module: 6 UI, 6 AO, 5 DO (4 x Relay 16 A, 1 x Relay 6 A)

LIOB-554

LIOB-BIP I/O Module: 7 UI, 4 AO, 7 DO (5 x Relay 6 A, 2 x Triac 0.5 A), 1 Pressure Sensor

LIOB-560

LIOB-BIP I/O Module: 40 Universal I/O (12 optionally with 4-20 mA Current Output)

The post LIOB-591 Room Controller appeared first on Kepler Electronics.

LIOB-AIR Controller

Maen Sirhan — Sun, 08 Oct 2023 21:00:26 +0000

LIOB-AIR is a fully IP based variable air volume controller (VAV controller) with a predefined, flexible, re-programmable application program and sophisticated management functions for a building ventilation system.